Replace serpentine belt 95 dodge 3.3 - 1995 Dodge Caravan

well it did not fall off
so pencil and paper draw out yours.
takes 5min work, no service manual to buy.
it depends on what 3 engines is there now.

seen here. (USA only car) exports ive no clue.

Serpentine belt tensioner replacement on a 1992 dodge ... on you tub

There is an EXCELLENT diagram of the serpentine belt routing for your truck, right on the FAN SHROUD.
If it has been removed or fell off, you will need to know which engine you have, and a Google search will yield the appropriate belt routing.

When did this first begin to happen? Changed belt or installed different pulley? Chased same problem. Solved it by shimming the idler pulley out so that belt ran in the middle of the pulley. Check the wear marks on the pulleys to see if the belts are running to the outside.

go to his web sight and down load the diagram book and then look up your make and model.


http://www.doocu.com/pdf/search/gates+auto+belt+routing

Click on the following free direct Link.
It has the correct Belt Diagrams for your 1992 Dodge Grand Caravan wirh either the 3.0L SOHC V6 or the 3.3L V6.

http://www.2carpros.com/car_repair_information/year/1992/make/dodge/model/grand_caravan/1992_dodge_grand_caravan_drive_belt_routing_diagram.htm

Included on the Diagrams are the Instructions on "Rotating" the Automatic Tensioner. See Below for additional Instructions to make your job easier.

"HOW TO": I professionally prefer the Serpentine Tensioner Tool.
Standard Rules to Removal the Serpentine Belt with an Automatic Tensioner:
1. Find the Tensioner(s).
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (located on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening located on the Tensioner Arm) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.
4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

Standard Rules for Installing the Serpentine Belt with an Automatic Tensioner:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.

Before You GO:
Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

Here is all of the diagrams for motors available for your vehicle, please select the correct size and adjust per directions.

http://s219.photobucket.com/albums/cc270/anubiscycle/?action=view&current=caravan-belt-replacement84-95.jpg

Here is digram of routing just take tension off tensioner and follow this daigram good Luck

http://www.2carpros.com/car_repair_information/tec_info/1998/dodge/grand_caravan/1998_dodge_grand%20caravan_drive_belt_routing_diagram.htm

This is the belt routing diagram for a Chrysler NY Salon 3.3L 1993
model. Hope it helps you. Gregg.