Directions how to change the sparkplugs - Cars & Trucks

just make sure that the plugs and wires are for your vehicle then change each sparkplug wire according to its length, the sparkplugs if they are new are already gapped.

Your Acura should not have spark plug wires. It should have coils direct on the spark plugs. Follow the link below for a step by step tutorial.

https://video.search.yahoo.com/video/play;_ylt=A2KLqILnXAZVY0kApyL7w8QF;_ylu=X3oDMTByZjF2ZHFmBHNlYwNzcgRzbGsDdmlkBHZ0aWQDBGdwb3MDNw--?

Your Acura should not have Wires. It has 6 Ignition coils mounted directly on the spark plugs. Follow the link below for a step by step tutorial on how to change the plugs.

https://video.search.yahoo.com/video/play;_ylt=A2KLqILnXAZVY0kAoSL7w8QF;_ylu=X3oDMTByZWc0dGJtBHNlYwNzcgRzbGsDdmlkBHZ0aWQDBGdwb3MDMQ--?

change faulty sparkplug or ht lead,check lead by holding sparkplug end near to engine nearly touching,have someone turn engine over whils checking for spark jumping,if spark present then not lead,change spark plug,if sparkplug ok then check pressure in cylinder, poss piston damage

Sometimes a plastic cover needs to be removed. Otherwise it's just unplugging the sparkplug caps and insert the sparkplug tool to loosen the sparkplug. Make sure nothing falls into the open sparkplug hole once it's out.

yes all front wheel drive 6 and 8 cylinders u must remove rear mount bolt loosen front mount bolt to change plugs pull engine forward and secure bolt in hole to keep elevated to change plugs

Hello, Depending on the Year of the car, the cars that had a sparkplug with a remote coil, you could have a bad sparkplug wire or a bad coil-pack or a bad sparkplug. For newer cars, the coil is attached to the sparkplug directly on top.

For those newer designs, the coil would need to be tested for that cylinder. Using an Ohmmeter, with 1 lead on top and the other on the tip which touches the sparkplug, it is a 10,000Ohm resistance.

Accessing the sparkplug coil is different for several engines. You may have to remove the Intake manifold to reach the coil and you may need to remove part of the fuel rail to remove the Intake manifold. Switching out a plug or coil is easy once you can get to it.

You can have your scans done free at Autozone, Oreillys, or Advance autoparts and they will clear the problem codes once you replace parts. I hope this Solution is very helpful to you.

Hi, to change spark plug first remove coil over connecting clip ensuring to depress connector release. Next remove coil over retaining bolts. Remove coil over carefully directing coil toward driver side until rubber end able to flex out of sparkplug access tube. Remove sparkplug using sparkplug socket with rubber insert. Had to remove ratchet to gain enough clearance. At this point you should be able to remove sparkplug by tilting extension & socket toward drivers side of car. Then lay horizontal & remove toward passenger side of car. If unable to gain access in this manner you probably have too long an extension. Take care as not to damage spark plug coil over as they are considerably expensive.

Open the hood to access the engine compartment. Locate the sparkplugs sitting to the side of the motor. Six wires run to the motor, three on each side.

Twist the rubber boot and pull away from the sparkplugs. This will expose the sparkplug.

Unbolt the sparkplug with a socket wrench. Use a 5/8-inch deep-well socket attached to the socket wrench.

Pull the sparkplug away from the motor. Discard the sparkplug.

Screw the sparkplug into the motor by hand. Make sure it is hand-tight.

Tighten the sparkplug with the socket wrench, using the deep-well sparkplug socket.

Click the wire to the sparkplug wire to the end of the sparkplug. Gently pull the wire to ensure it clicks into place.

Repeat the procedure for the remaining five sparkplugs. Change each sparkplug one at a time.

Whats the question?? just change the plugs, w/ platnium plugs.