What is the part name and part number for the plastic cover over the left rear turn signals - brake lights?

Here's a link to your lens,does this look like yours. PartsTrain com Hard to Find Auto Parts and Truck Parts Tail Light Lens For... Here's another link. 1991 Dodge Shadow Tail Light OEM Tail Light Used

Most likely it is the brake switch that has died. It is under the dash touching the brake pedal. If you have turn signals, the fuse is good.

It sounds like you have a bad connection where the plastic surround connects to the lighting switches. That piece from the central console to ring the upper part of the dash has to be removed and use electrical contact cleaner and plug them back in. There are three different connectors on the extreme left side of this plastic surround. Start by removing the plastic shroud under the steering column, unscrew the plastic shroud at the parking brake and then start on the upper hard plastic surround from the center console and remove the screw next to the grill adjacent the door (driver's side). Once the screws are removed, the hard plastic piece just pops out. (Remember, to remove the screws on the cover over the steering wheel; 2 to 4 screws as I remember... it also pops out in an upward direction. (Check any electrical relays as well.)

1) Open trunk
2) Remove small round plastic access panel with a flat tip screw driver by prying open
3) Remove flat tip screw holding tail light assembly
4) Remove tail light assembly by pulling outward, careful not to break plastic guide/nub
5) Disconnect wiring connectors
6) Remove plastic housing access plate on back of tail light assembly by twisting/turning tabs until they click and then lift access plate from tail light assembly
7) When viewing the the bulbs, the turn signal bulb is the bottom left bulb
8) Install in reverse order, ensuring tail light seal seats properly during installation

Hope this helps your out. I know the diagram and locator is a bit blurry but hopefully it gets what you need.
Drivers kick panel:
Front wiper 20A - Front wiper system Cigar 15A- Cigarette lighter Audio 10A- Audio, remote control mirror Air Bag 10A -Air bag diagnostics Stop lights- 15A -Rear brake light, high mounted stop light ECU B+ 10A - Shift lock actuator, transaxle controle module, radio, engine control module Room 10A - Interior light, clock, ignition key reminder, rear cargo area light switch ABS 10A- Anti lock brake system control unit ECU IG1 10A - Transaxle control module, shift lock actuator, ABS control unit, DRL unit Meter 10A - Instrument panel, back-up switch, electronics time control module, inhibit switch Turn signal 10A- Hazard switch ,front and rear turn lights, turn indicator IGN1 20A - Ignition switch ABS 30A- ABS pump motor TNS 30A- Tail light, license plate light COOL/FAN 30A- Cooling fan Cond/Fan 20A- A/C condenser fan Starter 15A- Start signal , Fuel pump Blower 25A- Blower Motor SR/ACC 10A - Ignition switch Hazard 15A - Hazard and turn signal light D/Lock 25A- Door locks ABS 30A - Anti lock brake system control P/W RH 20A- Power window motor right hand P/W LH 20A- Power window motor left hand IGN2 25A- Ignition Switch
Engine compartment :
Head 25A- headlights IG 2 30A- Ignition switch IG coil 15A -Ignition coil, condenser,generator IC regulator, diagnostic connector. O2 down 10A- Rear O2 sensor O2 up 10A- Front O2 sensor Fuel pump 10A -Fuel pump unit Injector 10A -Fuel injector ,camshaft positioning sensor, purge solenoid valve, EVAP, IAC actuator, Mass Airflow sensor, EGR stepper motor. fuel pump relay coil, vehicle speed sensor. A/Con 10A - A/C compressor controls, cooling fan BTN 30A- Brake light , high mounted stop light. Tail light LH 10A- License plate light, tail light , rear combo light, instrument panel illumination Tail light RH 10A-License plate light, tail light , rear combo light, instrument panel illumination Head low 15A- Headlight Head Hi 15A-Headlight Horn 15A- Horn

Inside kick panel

Have fitted the proper bulbs some have a staggered pin on them only go in one way

Rear Turn Signal, Brake & Parking Lights The taillamps, stoplamps and rear turn signals lamps are all incorporated into the rear taillamps. The taillamps are lit whenever the parking lamps or headlamps are in operation. The rear turn signal lamps flash with the front turn signal lamps whenever a turn is indicated with the turn signal/headlamp dimmer switch. The stoplamps light whenever the brake pedal is depressed and the stoplamp switch is closed.





The trim panel is likely held in place with retainers like this. Back out the screw to release tension on the pin legs and remove the fastener



The taillamp is retained by plastic wingnuts



Remove the plastic wing nuts from the taillamp housing



Remove the taillamp housing from the vehicle to service the light bulbs

1. Open the rear compartment (trunk).
   
2. If equipped, unhook the convenience net that stretches between the taillamps. It is attached to hooks molded into the plastic taillamp assembly retaining wingnuts. Loosen the rear compartment trim panel. It is retained by plastic pins with a screw in the center. Back out the screw to release any tension on the plastic pin legs, and pull the trim (thin carpet-like material) for access to the taillamps.
   
3. Remove the plastic taillamp assembly retaining wingnuts.
   
4. Remove the taillamp assembly from the vehicle and service the light bulbs as required.
   
5. Installation is the reverse of the removal process.
   
6. Test the lights for correct operation.
   

Hi, there, ye i have a similar problem, both my taillights and brake lights go on when i turn my lights on... i havnt found the solution to that yet.
But to answer your question on how to remove the taillight you undo the 2 screws on the inside of where the tailgate door closes and then pull the light out away from the car... ie to the side... there are 2 clips inside that you have to pull to make release.
the tail lights in the tailgate you have to remove the carpet and then undo the pannel.

means you have a blown bulb or you need to replace the.... oh i cant remember the exact name right now but go to autozone or whereever and tell them you need the fuse like thing that makes your blinkers work its only a few dollars

Rear Turn Signal, Brake and Parking Lights


STORM COUPE

1. Disconnect the negative battery cable.
2. Lift the luggage compartment floor carpet toward the front of the vehicle and remove the spare tire cover panel.
3. Remove the ten plastic retaining clips from the rear end trim panel.
4. Disconnect the luggage compartment lamp electrical connector.
5. Remove the luggage compartment trim panel and the rear end trim panel.
6. Disconnect the rear combination lamp assembly electrical connector. Fig. 1: Rear Turn Signal, Brake and Parking Lights — Storm

1. Remove the seven nuts and the rear combination lamp assembly from the vehicle.
2. Disconnect the rear combination lamp electrical connector.
3. Remove the four bulb sockets from the rear combination lamp assembly and remove the four bulbs from the sockets. To install:
   
4. Install the four bulbs to the sockets and install the four bulb sockets to the rear combination lamp assembly.
5. Connect the rear combination lamp electrical connector.
6. Install the rear combination lamp assembly to the vehicle and the seven nuts.
7. Connect the rear combination lamp assembly electrical connector.
8. Install the rear end trim panel and the luggage compartment trim panel.
9. Connect the luggage compartment lamp electrical connector.
10. Install the ten plastic retaining clips to the rear end trim panel.
11. Install the spare tire cover panel and the luggage compartment floor carpet.
12. Connect the negative battery cable.