1998 Ford Taurus Logo
Jean Ne' Kahle-potts Posted on Feb 06, 2013

I repaired the brake pads and calipar,there are no bad brake lines or brakes.The brakes were bled and still no brakes.I own a 1998 Ford Taurus SE

There are no brake lights on,but occasionally the ABS light will go on and off

1 Answer

A

Anonymous

The only problem you could have ,is that the brakes were
not bleed using the correct procedure,so I assume someone
was working in home driveway & doesn't know how

5 Related Answers

Anonymous

  • 4669 Answers
  • Posted on Mar 02, 2009

SOURCE: 98' Ford Windstar has a spongy brake

Have you had anyone try to clean and adjust the rear brakes? You will need a shop to scan the van for ABS codes first to cure the ABS light.

Ad

Anonymous

  • 3533 Answers
  • Posted on Apr 05, 2009

SOURCE: ford taurus 1998 brakes

it could be two things: you have a bad check valve in the master cylinder or the calipers themselves are bad

Anonymous

  • 334 Answers
  • Posted on Apr 19, 2009

SOURCE: rear brake lines 99 ford taurus se

most of the time the auto parts can give you the right length.but if i had to gess your looking at 6to 7 feet long 8 ft at the most. it would be a good i dear to re place the line going to each wheel to . because those will be the next one to go good luck

emissionwiz

Marvin

  • 85242 Answers
  • Posted on Apr 27, 2009

SOURCE: 1998 Ford Taurus/ Brake lights are not working.

most likely cause is that the multifunction switch is defective on the steering column. MOTORCRAFT Part # SW5599 Price $96.00

here is a photo.
0f44681.jpg .

Anonymous

  • 426 Answers
  • Posted on Sep 30, 2009

SOURCE: ABS & Check Brake System comes on occasionally

wait till it goes on again and go to your local pepboys, autobarn autozone rand s etc they usually offer free computer diagnostics, get me the codes, i cn help you then,

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

My 1998 ford taurus brake pedal goes straight to the floor .

Brake line busted somewhere? Is the linkage to the master cylinder intact? Master cylinder might have been installed incorrectly.
0helpful
2answers

Replaced front caliper bled brakes but peddle will not come back all the way and it feels like the brakes are on.

bleed them more you still have air in the line. and bleed all brake lines front and back.if after that no pedle could be a bad mast er cylinder
0helpful
1answer

I need to replace the brake line on my 1998 Ford Taurus

need to repair bad part of brake line, get new brake line at your local parts store
8helpful
2answers

1999 Ford Taurus, replaced leaking master cylinder, installed new brake pads, bled brake lines, pedal still soft. What else can I check?

There is a special tool required to bleed the brakes, it plugs into the ABS hydraulic control under the hood and holds the ABS valves open to remove the trapped air during bleeding, u will need to have the dealer bleed the brakes, they are most likely the only ones that will have this special too, but u can try an outside shop, I am sure Snap on tools makes this tool in the aftermarket tool catagory..
0helpful
2answers

Brake pedal goes to floor,replaced front pads rear good,bleed brakes no help

Hi:
If you have replaced all pads, and see no leaks at any wheel, and have bled your brake system, then most likely your brake master cylinder has failed.
1helpful
2answers
0helpful
2answers

Rear drivers side brake bleeder niple is froze - need to replace calipar - is this difficult? I have completed other repairs on brakes and replaced calipars before just not on a blazer

This is just like any other vehicle to change out the caliper. Almost all brakes are the same when it comes down to it. The only difference is the way certain companies either install them or the way they work. But on the Blazer it is really simple and can be done by just taking your time and doing it like you have done before
0helpful
1answer

Rear brake lines 99 ford taurus se

most of the time the auto parts can give you the right length.but if i had to gess your looking at 6to 7 feet long 8 ft at the most. it would be a good i dear to re place the line going to each wheel to . because those will be the next one to go good luck
0helpful
1answer

Ford taurus 1998 brakes

it could be two things: you have a bad check valve in the master cylinder or the calipers themselves are bad
Not finding what you are looking for?

231 views

Ask a Question

Usually answered in minutes!

Top Ford Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

xxxxxx xxx

Level 3 Expert

5117 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...