Craftsman Crafts & Hobbies - Page 8 - Recent Questions, Troubleshooting & Support

Does it use batteries or is it picking up current from the rails and a supply transformer?

Most remotes have a small "slide out" section on the rear, which one uses a fingernail to eject. Then inside will be the battery. Not which side is + and - and the battery type. If battery has corroded or left whits residue - a knowledgeable person needs to review & assist.

Hi, check out these tutorials to learn how to use it : https://learn.cricut.com/maker/getting-startedhttps://tgw.onl/digitalocean/ https://tgw.onl/siteground/ https://tgw.onl/ipage/

Hi,Allow the glue gun to heat up.Load a glue stick into the gun and pull the trigger. Use the new glue stick to help push out as much of the old stick as you can. If you can, push out the entire old portion and pull the new stick back out with your fingers.Use a metal stick, such as a paperclip pulled out straight, to scrape out the nozzle of the glue gun. Do this if the glue is old and doesn't flow well.https://appsync.biz/dafont/ https://192168ll.onl/ https://appsync.biz/filehippo/

How could you, except by contacting AMT? Failing that, how does your search engine of choice fail to find a substitute?

https://www.ebay.com/itm/PIKO-Model-H0-HO-1-87-Scale-Train-Track-lost-parts-Lot/223441376758?hash=item340624d5f6:g:xbEAAOSwRG1cg5wr&frcectupt=true

There should be two screws on the back of the control / power supply...just connect a wire from each screw to each screw (two of them) on one of the track pieces. it the train is running the wrong way...switch the wires on just one screw set..

http://powertool.manualsonline.com/manuals/mfg/metabo/metabo_saw_product_list.html

Sound and motion decoder are the same address. Try F8 that mutes and unmutes the sound, If that doesn't work Change CV 8 to 8, that resets the decoder to factory settings. You will have to re enter the address as the decoder reverts to address 03. If all else fails check that the speaker is wired properly, if that doesn't work you may have a bad decoder that should be under warranty. Good luck

Is that even a real word?

Hows this? "I was asked, how would I use the word adhesively in a sentence."

Acrylic paint depends on time, temperature, humidity, paint thickness, air-flow and absorbency to dry. Reeves Complete Acrylic Painting Set Oil colour paint takes long time to dry than other media and it allows to think and it also provides the flexibility for changes. Williamsburg Handmade Oil Color Paint Alizarin Crimson 37ml Tube

Gouache is a painting technique in which a gum additive is joined with watercolors to produce an effect that is opaque in appearance.

Reverse is working in the opposite direction. That's not as obvious with circular needles so it makes sense to me to switch to straight needles. When you finish the previous row, do not turn your work. I'm going to give directions for right hand; turn it opposite for left hand. To start the reverse row, stick the free needle, in the right hand, into the work in the normal way for a stitch (in back for knit, in front for purl) and execute a stitch as you normally would, pulling it onto the right hand needle. You're doing regular knitting, just in the reverse direction. Hope that makes sense and helps.

Check CV 2, 5, &6 for a main line train they should be : CV 2 set to 02 start voltage CV5 set to 154 Max voltage CV6 set to 128 Mid voltage

You may have to go to a Digitrax N /HO scale decoder for it to fit. The decoder handles motor functions OK but a sound N scale has very low volume as the speaker is very small. I have done this a few times with good results. Or put the decoder in the tender and run the 30ga wires to the engine

Check and see if there is a model number, serial number or barcode number on the kiln. Usually if you just put the number into a search engine e.g. Google, it can find the manufacture, etc.

Sounds like the power button may have gone bad.

Hello, Virginia - I have not yet found any online written instructions on how to use the Boye (not Boyer) Electric Yarn Ball Winder. You may find this video tutorial instructive: http://curvetube.com/Instructions_for_using_the_Boye_Electric_Yarn_Ball_Winder/hCF1jFCEpQ0.video The Boye company is owned by the Simplicity Creative Group. If you wish, you can contact the company and ask about the availability of printed written instructions for use of the Boye Electric Yarn Winder: https://www.simplicity.com/contactus/?topic=PRODUCT+QUESTION Best wishes.

Check the wiring again, or the switch mechanism is faulty. The acc transformer operates a solenoit when changing the switch direction so no irect contact with the track power. If your wiring is correct, the switch should be replaced, in my opinion

You should be able to change the font size in the software program.