Over size character and graphics - Computers & Internet

Hello,To change the font size, do the following: 1. Press the “Function” key 2. Press the “Left Arrow” or the “Right Arrow” key until the display shows “SIZE”. 3. Press the “Function” or the “Return” key. The current selected size setting is displayed and a triangle indicator pointing a sample of the character size above the display. 4. Press the “Left Arrow” or the “Right Arrow” key until the desired Size is displayed. * SIZE1 equals Standard Size. * SIZE2 equals Double Width. * SIZE3 equals Double Height. * SIZE4 equals Double Width & Double Height. * SIZE5 equals 4 x Width & Double Height. * AUTO, the machine will automatically adjust the characters to the largest possible size according to the width of the tape installed in the machine. Press the “Function” key or the “Return” key to select the characters size. I hope this helps.

ANSWER: Since it is a thermal printer it does not have a ribbon to replace.

Description:
The Seiko SII DPU 414 thermal Printer. For a compact desktop or portable thermal printer, the DPU-414 is an excellent selection. It incorporates the STP printer mechanism to ensure silent and high-quality printing of characters and high-density graphics. And in quadruple-density bit image mode, 640-dot (maximum) CRT display hardcopy is possible (with horizontal vs. vertical radio of 1:1).

Product Specifications

• Model DPU-414-30B
• Printing Method Thermal serial dot printing
• Number of dots/line 9 x 320
• Paper width (mm) 112
• Printing width (mm) 89.6
• Max Speed (character/sec) 52.5
• Paper path Curved
• Character matrix (H x W dots) 9 x 7
• Character size(H x W mm) 2.5 x 1.9, 2.5 x 0.9 (Condensed)
• Number of columns 40, 80(Condensed)
• Character type Extend Graphics Character set, Alphanumeric, International Characters, Katakana Character set
• Interface Parallel (36pins Amphenol), Serial (9pins D-SUB)
• Input buffer 28Kbytes
• Command ESC/P * conformity
• Cutting Tear bar
• Operating Temperature (°C) 0 to 40
• Humidity (%RH) 30 to 80(Non condensing)
• Service life (line) 500,000 **
• Dimensions (W x D x H mm) 160.0 x 170.0 x 66.5 (printer unit only) ***
• Mass (g) Approx.580(without Battery)
• Compliance FCC, CE, VCCI

Manual:
http://sii-thermalprinters.com/pdf/manuals/DPU414/DPU-414_User_Guide.pdf

Its one of three, (1) 3.8 SC OHV, (K) 3.8 OHV, or (M) 3.1 OHV. The eighth character of your cars VIN represents its engine size. The character in parentheses listed prior to the motor sizes above represents the eighth character of the VIN. Just look at your VIN and match it to the above motors.

Hello,

To change the font size, do the following:


1. Press the "Function" key

2. Press the "Left Arrow" or the "Right Arrow" key until the display shows "SIZE".

3. Press the "Function" or the "Return" key. The current selected size setting is displayed and a triangle indicator pointing a sample of the character size above the display.

4. Press the "Left Arrow" or the "Right Arrow" key until the desired Size is displayed.
* SIZE1 equals Standard Size.
* SIZE2 equals Double Width.
* SIZE3 equals Double Height.
* SIZE4 equals Double Width & Double Height.
* SIZE5 equals 4 x Width & Double Height.
* AUTO, the machine will automatically adjust the characters to the largest possible size according to the width of the tape installed in the machine.

Press the "Function" key or the "Return" key to select the characters size.

I hope this helps.

You should download and update the drivers for your graphic card from the manufacturer's website. However, you can also try changing the resolution of your display to the most viewable resolution instead, which will depend on your monitor size.

consult the manufacturer for details customization

This sounds like it could be a couple of things. First, since the cursor is huge, go up to the menus at the top and choose Window>Character which will open the character palette so you can change the size of the text. Then make sure the text color is different than the backgrd color 'cuz it could be getting lost. Check your Layers palette to see if the text tool worked as whenever you use the text tool it will make a separate layer for the text. If your font size is small and your cursor is still going off the canvas, it could be that your image is very small. Check this by going to Image-->Image size and you can change the dimensions or the resolution. If the resolution is already low (>72ppi) then the image will pixelate when you make it bigger so try to get a higher resolution copy of the pic.

Try these steps dude :

• Open insert menu --> choose Character --> the character to be inserted
• or
• Open insert menu --> choose Character --> then more to see more special characters

set four corners image when bosewr is holf image size same

Press the Return button and the machine will automatically print the size the tape will allow! :) Title:
What does the error message "CHR SIZE AUTO?" mean? Description:This message appears when the selected character size is too large for the width of the tape cassette installed.

You have the following options:

• Press the "Print" or "Return" key to allow the P-touch machine to automatically select the maximum character size that fits the tape width.
  
  
• Press the "BS" key to clear the message, and then install a wider tape cassette.
  
  
• Press the "BS" key to clear the message, and then select a smaller character size by following these steps:
  
  
  1. While holding the "Code" key, press the "Size" key. The display will show the current character size.
     
     
  2. Keep the "Code" key held, and press the "Size" key until the desired size is displayed.
     If you select "AUTO", the P-touch machine will automatically adjust the character size to the largest possible size.
     
     
  3. Release the "Code" to apply the setting.

If you have the correct size tape installed and still get the error message, please try removing the cassette from the machine and reinstalling it. Also, check that the tape cassette is seated firmly in the compartment.


Note

The following table shows the maximum character size that can be used with each tape width.

Tape Width Maximum Character Size 1/4" (6 mm) 12 points 3/8" (9 mm) 18 points 1/2" (12 mm) 24 points 3/4" (18 mm) 42 points

Related Models PT-1900