Question about Graco Infant SafeSeat (Step 1) 8A05RXY in Roxy

1 Answer

I need to assemble the straps and cant figure it out????

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers
Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cant figure out how straps go back on carseat since I washed it? its the brown and tan high back with tilt...omgoodness I cant believe I have done this please help!!!!!!


Hi,


This isn't a product available in the UK so we're unable to assist with your enquiry. Could you let us know what country you're in so we can direct you to the appropriate customer care team?

Aug 04, 2012 | Safety 1st Baby Gear

1 Answer

Hiya i took my car seat cover off and i cant figure out how to loop the strap by the feet at could you help please


Hi - You may find it easier to get the tensioner strap into the location using a flat spoon handle. Take the carseat to your retailer for them to advise if you have difficulty.

Feb 12, 2011 | Maxi-Cosi CabrioFix (Black Reflection)...

1 Answer

Need to replace ignition switch


Ignition Switch (2005 Chevrolet Venture listed but the 2006 Venture was not) Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • The SIR system
    • The upper and lower trim covers chev_vent_ign-swch-harness.gif

    • The wiring harness assembly (D) from the wire harness strap (E)
    • The wiring harness straps (C) from the wire harness assembly (D)
    • The wiring harness strap (B) from the upper tilt head assembly (A) chev_vent_col-bulk-conn.gif

    • The turn signal switch assembly connectors (B) out from the bulk head connector (A) chev_vent_passkey-mod.gif

    • The PASSKEY III (B) off of the ignition lock cylinder case (A) chev_vent_ign-swch-screws.gif

    • The key alarm connector (A) from the ignition lock cylinder case (B)
    • The 2 tapping screws from the ignition switch assembly (C)
To Install:
  1. Install or connect the following:
    • The ignition switch assembly (C) onto the ignition lock cylinder case (B)
    • Two tapping screws into the cylinder case.
      1. Torque to: 42 inch lbs. (4.7 Nm)
    • The key alarm connector (A) into the ignition lock cylinder case (B)
    • The PASSKEYS III (B) onto the ignition lock cylinder case (A)
    • The turn signal switch assembly connectors (B) to the bulkhead connector (A)
    • The wiring harness assembly (D) into the wiring harness strap (E)
    • The wiring harness strap (B) into the steering column tilt head assembly (A)
    • The wiring harness straps (C) onto the wire harness assembly (D)
    • The upper and lower trim covers
    • The SIR system
prev.gif next.gif

Sep 25, 2010 | 2006 Chevrolet Venture

2 Answers

Need an exploded diagram of a te20 rear axle


I have a model to 30 tractor.The rear lugs to hold the tire rim need to be replaced,How hard is it to replace and do I take the
whole assembly apart to replace lugs

Jan 31, 2010 | RTO Massey-Ferguson Tractor TE20, TO20,...

1 Answer

Avalon Mask strap assembly broke


Try to spread apart the clip using two sets of small nosed pliars on each side of the clip, therefore not applying any pressure to the mask. Best wishes with a wonderful sport!

Dec 27, 2008 | U.S. Divers Avalon Purge Mask

2 Answers

How to change Mini Em-Tor Fill Tube Assembly on Kirby G4


You will have to remove bag strap. You can try to save old strap (see instruction here) or you can cut it. Install the bag on the new mini-emptor just like it was on old one (strap goes over both layers of vinyl). Use a long cable tie instead of the strap if you have damages it or your old bag strap. If you are using old strap you may have to use pliers to get it in all the way.

Oct 27, 2008 | Kirby G4 Bagged Upright Vacuum

4 Answers

Carseat harness straps


You have to unloop the straps from the gold metal bar. This will allow the straps to be free so you can feed them thru the holes and re-feed them into the proper height hold. You will than noticed that there are loops at the very end of the straps which you can loop back onto the gold metal bar.

Sep 23, 2007 | Baby Gear

Not finding what you are looking for?
Graco Infant SafeSeat (Step 1) 8A05RXY in Roxy Logo

263 people viewed this question

Ask a Question

Usually answered in minutes!

Top Graco Baby Gear Experts

Joyce Nokleby

Level 2 Expert

70 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

john milligan

Level 3 Expert

514 Answers

Are you a Graco Baby Gear Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...