How much Jet clean solution do i use in the Norelco Jet clean system? Is it straight solution to the line or a mix of solution and water?

There are several types of these. You will need to know the model number of your shaver to select the correct type. You will find them at shaveroutlet.com
http://shaveroutlet.com/catalogsearch/result/index/?cat=99&manufacturer=4&q=clean+and+charge&submit=

Good question, but at these prices, you may not want to bother:

http://www.ebay.com/itm/3-Norelco-Jet-Clean-Solution-HQ200-Bottle-Replacements-/231035497446?pt=US_Shaving_Hair_Removal&hash=item35cac9ebe6

Did your Jet Clean System used to work, but now rejects the razor and flashes a red indicator that your reservoir is empty when it is not?

The reason is that the liquid level sensor is full of gunk (you don't want to know what the gunk is made of). You can easily clean this yourself and restore normal operation. Here's how:

1. Remove the razor and reservoir. Leave it plugged in.
2. Press the start button and when the holder hits the bottom and stops, immediately pull the plug before it comes back up.
3. Turn the unit over and clean off the gunk you can see with a Q-Tip.
4. Fill the cleaned reservoir beyond the line (almost to the top) with hottest tap water and place it on a towel on your counter.
5. Mix in 1/8 teaspoon of dishwasher detergent. Do not use Dawn or other dish detergent. It must be the type you use in your dishwasher! (Trust me on this).
6. Lower the unit onto the reservoir and let it soak for at least 20 minutes.
7. Hold the reservoir down on the towel by depressing the release buttons and pull and put the cleaning unit in and out of the reservoir 20 or more times to flush out the crud.
8. Refill the reservoir with clean, hot water and do the pull - push trick again many times. Rinse and refill the reservoir with hot water and do this again 2 more times until the water is clear and there is no debris to be seen in the water.
9. Remove the reservoir and allow the cleaner to dry thoroughly. Depending on the humidity where you do this, drying can take from several hours to an entire day. A hair dryer on the part you cleaned with the Q-Tip may help, but time will still be needed.
10. Assemble and try it. It should work like new. If it does not work properly, (mine acted like it was jammed) don't worry, it is likely not completely dry inside. Remove the reservoir and wait for it to completely dry before trying again.

Have fun!

it means it can be clean out with water under the faucet

Yes, after you push the start button on the unit, pull the plug out of the wall socket when the arm gets to its bottom position. It will stop at this lowered position. When you plug it in again, it will go back to its upright position. Norelco ships the new cleaning units in this contracted position. When you plug it in presto! You are ready to go.

Visit this site below and enter your product number. If you don't have your product number or it doesn't appear, then type in "jet clean" then scroll down and click on personal care. You can then click on a jet clean model and then open the .pdf of the manual. The instructions should be similar. There is nothing to using it. Fill the reservoir with jet clean solution to the max line. Put the shaver in the cradle heads down and press the button on the front of the cleaning base. If it doesn't stay down and clean you may have another problem. If so, then search "Norelco Arcitec Electric Shaver with Jet Clean" on this site and you can find answers to your problems.
http://www.support.philips.com/support/sms_page.jsp?userLanguage=en&userCountry=us

if you need blades, you will find these at shaveroutlet.com. see link below

http://shaveroutlet.com/norelco-philips-rq10-arcitec-replacement-heads-p-353.html

You need to fill the based to the max solution line. There is not enough solution in the container.

Hi, it may be worth your while looking at e-bay to see if anybody is selling a broken shaver with all the bits still working, You can usually pick things up that way, plus, they are often Very cheap! Best of luck, Nick.

I had the exact same problem. Then I put more solution in so that it was just above the MAX line and it worked fine. So make sure you have enough cleaning solution in the system and it should work great.