My cx3 takes off to the left and i cant stop it . I try trimming it out but still have to hold stick to the right to lift off straightr up, and when it flys it still goes to the left if I dont hold the stick right.

The best solution you'll get from books at www.reliable-store.com

These are books containing info on repair, service, troubleshooting, parts info, assembling dissemble, removal, error/fault codes, wiring diagrams and everything on any vehicles cars, atv, trucks. forklifts, boats, excavators etc

I don't believe this part is available aftermarket, only from Acura. Part # 77230-SEP-A02ZA $93.17. It isn't hard to replace. First you pry up left and right chrome side trims on the console. Start at the back, they are held on with clips, be gentle but firm, don't flex the trim. A plastic trim tool helps. Once you've done 1, they are easy. Then it is just screws holding the rear section, slide both seats all the way forward to help lift out console. Go to Acura E Parts to see an exploded view.

It's difficult to determine witch trim buttons effect the props. The only way to do this is durring flight. At low power, since you are working with 4 axis, each set of 2 buttons will effect the rotational speed of 1 motor. Typicaly in this set up, the left stick will control power and yaw(up and rotation left and right), while the right stick controls direction and pitch.(forward/reverse and bank left or right) Here is what I think you need. The left side bottom butons, control horizontal control. If you take off and notice the helo going to the left(banking, not turning) click the right button to attain horizontal stability. If you notice it is going slightly forward click the bottom button on the right side of the left stick. The same can be said with the axis control on the right stick. I hope to see this aircraft on youtube, as there is a shortage of these flying stabile anywere. good luck.

What are control horns????

dissconnect negitive battery terminal, open dirvers and passenger doors.remove dash end caps then use a pry stick or screwdriver and pry out left and right A pillar trim panels. next is to remove the bezel, lift up on the outter bottom edges of top bezel and along rearward edge of top cover top disengage clips, pull top cover rearward intil pins disengage from instrument panel and then remove from dash, next is to remove the cluster bezel and then the top and bottom steering column covers, the next step is to remove the screws holding the switch. then the connectors to switch.lift switch straight up and remove. to install reverse removal procedure. heres a diagram to help you understand the covers and bezels locations. hope this helps good day.

Hi

1. Remove the black trim panel holding the cruise control and sport mode buttons from around the shifter. There are 4 clips holding the panel on: upper left, lower left upper right and lower right. Be careful, they break easily. Remove the wires from the buttons.
2. There are two brackets holding the wood panel down, one on each side of the shifter. Remove the two screws holding down each bracket. Be sure you note the orientation of the brackets - it will make reinstallation easier. Lift off the wood trim panel.
3. Under the wood trim you just removed, there are four bolts fastening the console to the car. Remove them.
4. Open the console lid. Remove the two screws fastening the latch strike plate. Again, make note of the positioning of the latch plate for reinstallation
5. Remove any other screws retaining the console compartment. Lift out the compartment liner. Close the console lid.
6. At the rear of the console is a trim cover. It is held by two tension clips. Just pull it off.
7. There are two bolts under the rear trim cover - remove them.
8. Remove the console.
9. Remove the screws holding the radio in the dashboard and pull the radio forward.
10. Remove the antenna wire and wiring harness connectors from the back of the radio.
11. Unbolt the ground wire from the back of the radio.

Reinstall in reverse order.


Let us know if you have something more to know else accept the suggestion.
Thank You for contacting Fixya.com

have you tried using the trim buttons?,after take off when its around 2ft in the air if the tail spins to the right tap the left trim button a few times and if its spinning left tap the right button a few times and this should stop it spinning it works ok on my one

i would continue to hold the trim. this happended to mine and i held the trim for a couple of seconds and it leveled out. also i have a problem, mine wont generate enough lift to take off. do you have a solution for that?

There are two optaions for you to find one, one of the simpler ones would be to find a video game store and ask if they have the booklet in stock and they should be able to give you one, or you can try e-bay, im sure there is something on there. I hope I have helped you in anyway.

Wayne

have you made sure that the helicopter is charged completely?

if so when you try to take off if it spins to the left then hit the r trim on the remote and if it spins to the right then hit the l trim on the controller.

honestly all the instructions do is tell you how to put batteries in the controller.