Just bought a 19" got it all set up and now there is a 3' stripe across it can't see clock to adjust or auto configure what is H/V position. Old lady electrically challenged

Sounds like a hardware fault not sure but , in case somebody has inadvertently entered wrong settings, set to factory default and then do an autotune. If it sorts out then you know it was somebody's input. If it carries on doing the same thing you know it is a hardware error and will need the services of a competent

HI,

Please give me a min.i'll let you know if there's a manual available for your model

At the bottom of the monitor, there are some buttons. Pushing the right-most button (Auto/Set) will enable the automatic configuration to happen. This will "automatically optimize the monitor's image position, clock, and phase."
Gateway FPD1530 User Manual Page 11 Adjusting Monitor Settings External...

What settings do you mean? The important adjustments are the seat height and position of the handlebars. You might mean the gear selectors, one will have 1-2-3 (or may 1-2) and the other will have 1-2-3-4-5-6 (or maybe up to 7 or just up to 5). These are meant for the rider to make changes while riding for going up or down hill or into a headwind, etc. If the bike is in good shape, you shouldn't have to set anything except maybe the seat height.

Hi there,

There are two ways to set the clock on your machine, firstly by using the 'auto clock' feature and also a manual setup, if the auto setup doesn't work then you will need to setup your machine manually. the 'auto clock' feature will atempt set itself up and will take approx 4 mins for the machine to adjust itself. There is also a daylight saving setting which you can either have set to on or off. The auto and manual steps that I have added below have been taken from the user manual for your your Toshiba SD-V295 pages 24 - 26.

Hope this helps,

James

Auto Clock Adjustment
Preparation:
• Turn ON the TV and select the corresponding video input.
• Press VCR DVD selector to select the VCR mode.
(The VCR mode indicator will light.)
1. Connect the Antenna or Cable system.
If you use a cable box, turn it on.
2. Plug the AC power cord to the AC outlet.
3. Make sure the DVD/VCR is turned off.
If you press POWER, the Auto Clock set is not programmed.
4. Wait at least three minutes and press POWER.
5. Press CALL DISPLAY to check the clock setting on the on screen display.
6. If the clock is not set, check the antenna
condition. The AUTO CLOCK may not function properly if the reception condition
is not good.

Manual clock setting
1. Press VCR MENU.
2. Press SET + or – to select “SYSTEM SETUP”, then press ENTER.
3. Press SET + or – to select “CLOCK SET”, then press ENTER.
4. Press SET + or – to set the month, then press ENTER.
5. Set the day, year and time as in step 4.
6. After setting the clock, date and time starts functioning automatically

The vertical hold is probably going out on her tv. Some televisions that are very old have a knob that can adjust the vertical hold.

For presice adjustments of VGA input run the Auto Ajustment Software on the CD

Additional image quality improvement use the clock and clock pahase controls of the monitor to fine tune the image
Clock increase or decrease the value to minimize any vertical bars or stripes visible on the screen backgroung
Clock phase increase or decrease the value to minimize video distrotion or video jitter

• allow the monitor to heat up before adjustments

• use the adjustment pattern application provided ont he CD

• select OSD menu to select image control and change clock or clock phase

• Incase of any error restore factory settings select the OSD menu and select factory reset and select yes
  

Please try this....

Setting the Clock
1. Press and hold the Clk Set Button.
2. While holding the Clk Set Button, press the Skip/Search/Hour/Minute Buttons to adjust the hour and minute.
3. Release the Clk Set Button to set the time.
Setting the Alarm
1. Press and hold the Alm Set Button.
2. While holding the Alm Set Button , press the Skip/Search/Hour/Minute Buttons to adjust the hour and minute for the alarm time.
3. Release the Alm Set Button to set the time.
4. Adjust the Auto/Off/On Button to Auto.
5. Adjust the AM/FM/CD Switch to the desired function for the alarm, or reduce the Volume Dial to "Buzz" to wake to the unit’s buzzer.


Cheers!

Reset your monitor to its factory settings by using the auto config..
Take the bios battery out of your laptop or desktop and restart with the battery off..
then reboot..

If this works please rate me.

you should be able to just push the Time button (top one third from the right) and when it starts to blink, just change it like you change the alarm.