I need to fix the lower controller in my treadmill lime D3.3 Where can I buy it?

1)E00 Safety Key not in the position Re-locate the safety key in the correct position.
2)E01 No signal to Controller from the console
A: Check the Main Controller Wire
B: Replace the PCB Board
3)E02 Motor communication error
A: Check the wire from motor to controller
B: IGBT breakdown, Replace the controller
C: Check the power voltage if 50% lower than rated voltage
D: replace the motor wire or change motor
4)E04 Incline Motor communication error
A: Check the wire from incline motor to controller
B: Replace the incline motor
C: Replace the controller
5)E05 Over current protector
A: Overloading or over resistance,
restart the treadmill
B: Transmission parts seized up, check the parts
C: Replace controller
D: Motor breakdown, change the motor
6)E06 Motor Open Circuit.Connect the Motor link
7)E08 IC Driver Error. Replace the IC driver or change the
IC driver
8)E09 Folding up protect.
A: Do not fold up the running deck when treadmill in is running
B: If the running deck in laying position and show E09, you need to change the controller
9)E10 Motor instantaneous current abnormal
A: Adjust the torsion potentiometer of the Controller to lower
B: Motor Breakdown, change the motor
10)E11 Overvoltage protector Voltage over 270v (for 220v) or 150v (for110v) -- turn off the treadmill and check the power source
11)E13 No signal to console from the controller
A: Check the Main Controller Wire
B: Change the controller
12)E14 Lower voltage protector Voltage lower than 160v (220v) or 70v (110v) -- turn off the treadmill and check the power source

Best to contact a dealer that specializes in treadmill belts. Have your manufacturer, year and model number ready.

http://www.walkingbelts.com/?gclid=Cj0KEQiA1NWnBRDchObfnYrbo78BEiQA-2jqBSZdgL8ypUw24ssYXIWG1At_Wgo69QJrx3RmV00V2vYaAh888P8HAQ

http://www.treadmilldoctor.com/treadmill-belts?gclid=Cj0KEQiA1NWnBRDchObfnYrbo78BEiQA-2jqBazYy690viI0Gv74Fh6XGgmMzT-pmGirXaDPGfWxvfQaAtg88P8HAQ

Please see these posts for more info:

http://www.treadmillsrepair.co.uk/2014/08/treadmill-motors.html

maintenance:

http://www.treadmillsrepair.co.uk/2014/08/weekly-treadmill-maintenance.html

http://www.treadmillsrepair.co.uk/2014/08/monthly-treadmill-maintenance.html

Test the input voltage to the motor, if there are in therminal motor the motor is faulty, repair or replace.
Measure the output voltage from controller board, for input voltage motor, if there are NOT the control board is faulty. see the diagrams attached.
see my personal TIPS for test motor.
God bless you

please see the video and fix it. LUBE the deck belt+rollers bearing front+back +test the drive belt motor, and replace it if necessary.
God bless you

Run the software calibration for easy diagnostic and fix it.
God bless you

lube the deck belt and proceed according. However you must readjust the speed sensor + Reed switc. Run the software calibration for easy diagnose and fix it. see the diagram attached.
God bless you

1) You have out of adjustment the sensor reed switch,see the schematic.by 1/8" or 3mms aprox.
2) With this you will fix it.
3) However if the problem persist, you must check if the display board is o.k or faulty.
4) Test the 5VDC for IC( Including EPROM, ROM,etc) Tight flexible cable for Display Board vs Lower Board(Main Controller Board).
5) Since the Lower Board send the Power Supply coming from the Transforme you must Test it, and then power supply for +5Vdc.
6) You must have Strong Conclusion if the problem is Upper Board or Lower Board(Main Controller Board) .
Finally The Lower Board Control 90% functions of the Treadmills.

Dear Richard,
Did you get a solution to this problem
Fitz London

The problem is either in the lower control board or the lift motor. I would start by replacing the lift motor. Then if that does not fix it, replace the lower control board.