Question about Zebra Printer 140-751-00000

Open Question

Zebra 140XiIII Plus error No Ribbon. printer stops when printing

The printer starts to print labels and stops. Displays error. I have to open the arm that hold the label and ribbon down and press the Pause button to get it to start again. could it be a sensor going out?

Posted by on

6 Suggested Answers

checkitright
  • 1346 Answers

SOURCE: Z6M printing issue

try adjusting the presure of the printhead

here is the site for the manual

http://www.zebra.com/id/zebra/na/en/index/resource_library/manuals.results.html


good luck

Posted on Dec 12, 2007

ozztech
  • 285 Answers

SOURCE: Zebra 4M Plus Pauses unexpectedly

try to run the manual calibratio from the setings.
run "manual calibration"
move the ribbon out from the sensor (with the print head open) and take out 3 or 4 labels from the rollar and put that blank label paper unther the sensors on the left,
say "ok"
wen appear "reload all"
put the ribbon and the normal labels on the correct possition, and say "ok"
try to run sext the sensor profile.
save data (twice on "setup button")
tur off, and on again.

Posted on May 08, 2008

Sakeninja1
  • 5 Answers

SOURCE: printer starts and then stops

Could be that the printer needs to be calibrated or that the Belt on the inside of the printer could have a bad spot on it. Since the belt pulls the ink and label at the same time it hits the bad spot on the bad belt and causes it to stop.

Posted on Mar 27, 2009

ozztech
  • 285 Answers

SOURCE: Zebra S500 not sensing media

download the driver www.seagullscientific.com
recalibrate media, if necesseray Reset to Factory defult.

Posted on Nov 13, 2010

ozztech
  • 285 Answers

SOURCE: label header or footer is out of page

chech if the tipe of label is correct from the driver (length and with)

Posted on Nov 23, 2010

  • 51 Answers

SOURCE: I have a Zebra 105Se

Make sure that both ribbon and media paths are clean (no glue, or sticked labels). Make shure the ribon and the media are corect installed on their paths.

Posted on Sep 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an old Zebra 140Xill, will this do direct thermal transfer, do not have the manual


Press cancel for 5 seconds while power on to print config. Then check the following parameter.

direct thermal = no ribbon
thermal transfer = ribbon

Sep 16, 2010 | Zebra 140XiIII Plus Thermal Label Printer

1 Answer

Label header or footer is out of page


chech if the tipe of label is correct from the driver (length and with)

Apr 27, 2010 | Zebra 2746e Thermal Printer

1 Answer

I have a Z140XiIII that used to have a ribbon and thermal transfer stock. we changed the stock to not require a ribbon, so we removed the ribbon and set the menu to Thermal direct. labels print OK but the...


If the printer is flashing "Ribbon in" then it sounds like the printer setting to Thermal Direct is being changed back to Thermal Trans. Verify this after sending a format. This is very common because the printer is bring over-ridden by the software and/or printer driver when you send a format.

Look for a setting in the software / driver for direct thermal and make the change there.

Hope that helps.

Apr 21, 2010 | Zebra 140XiIII Plus Thermal Label Printer

1 Answer

140xilll plus printers when the ribbon runs out


Check in the parameter if you are not in direct thermal print

Mar 10, 2010 | Zebra 140XiIII Plus Thermal Label Printer

1 Answer

Ribbon Label Stock Misalignment


There isn't any type of guide made to do that.

Feb 03, 2010 | Zebra 140XiIII Plus Thermal Label Printer

1 Answer

How do you clear the printer buffer on a zebra 140Xi111 plus


1. click on "start" select "run" and type "services.msc"
2. after open services windows select "print spooler" services
3. stop "print spooler" services
4. click on "start" select "run" and type "C:\WINDOWS\system32\spool\printers"
5. after open the printers folder deleted all the pending print jobs
6. restart the "print spooler" services and try to print now.

Aug 06, 2009 | Zebra 140XiIII Plus Thermal Label Printer

4 Answers

Want to reset my Zebra 140XiIII back to factory settings?


I resolved the problem by going into the setup program and then exiting and at that point I was prompted to save my changes and one of the options was to load Default settings. Once I chose this I was able to print on the 4X6 labels correctly, before that the configuration was feeding a label and 1/2 and print across two labels.

May 04, 2009 | Zebra 140XiIII Plus Thermal Label Printer

2 Answers

Small label is being cropped at the top


Have you tried the menu settings for start top of label? If other printers work, you are talking about a configuration setting. I would get a configuration off another printer that works and look at yours real close.

May 01, 2009 | Zebra 140XiIII Plus Thermal Label Printer

1 Answer

Printer starts and then stops


Could be that the printer needs to be calibrated or that the Belt on the inside of the printer could have a bad spot on it. Since the belt pulls the ink and label at the same time it hits the bad spot on the bad belt and causes it to stop.

Feb 03, 2009 | Zebra Printer 140-751-00000

1 Answer

140XiIII left side print right side completely blank


Verify your LCD Display Print Width setting is set wider than your actual label width. The printer will only print to the width of the PRINT WIDTH setting. Also verify any driver or software settings as these override your printer settings.

Jun 30, 2007 | Zebra 140XiIII Plus Thermal Label Printer

Not finding what you are looking for?
Zebra Printer 140-751-00000 Logo

Related Topics:

507 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zebra Printers & Copiers Experts

pkwc

Level 2 Expert

254 Answers

lancer284

Level 1 Expert

35 Answers

kenneth njonjo

Level 3 Expert

1575 Answers

Are you a Zebra Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...