Question about Dewalt DC920KA Heavy Duty Xrp 18V Cordless Drill/Driver

2 Answers

Drill hole in China Plate

I want to get what I would need to drill a hole in a china Plate to make a bird feeder Without breaking the plate.

Can you help me.?

Posted by on

  • Anonymous Jan 19, 2009

    what are the potential drill hole problems



2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 417 Answers

Normally you would use a masonry bit to drill into ceramics eg tiles or bricks. if the plate is glazed it is better to stick some masking tape or adhesive backed paper on the area to be drilled to stop the drill bit slipping around. also i would be inclined to use a hand turned drill or a small battery powered drill if you have one to avoid breakage of the plate.

Posted on Oct 13, 2008

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 1 Answer

Use a masonery drill bit

Posted on May 09, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I am trying to drill through old encyclopedias, but the drill bits keep snapping in the pages. What type of drill bit can I put on an hand-held drill that will get through the books without breaking?

rx-dk-diy054036_wood-drill-bits_s4x3_lg.jpgI've used 'regular' high speed drill bits for paper, and wood boring bits. I think the wood bits work better, but whatever bit is used the drill flutes have to be cleared out of material. This is done by drilling a little bit at a time and then lifting the drill out of the hole to clear the hole and the drill of shavings. This is essential to do to minimize heat buildup and binding of the drill bit. The drill bit should not break if you take it nice and easy, and drill in small increments .

Dec 17, 2013 | Hinge European Drilling Tool 35mm Cup ...


How to drill in a PCB Board

<p>PCBs or PCBs are pieces of hardware that electrical components such as transistors, capacitors, resistors and contain conversations recorded. PCBs in various electronic devices such as computers, radios, VCRs, DVD players can be found, game consoles and televisions. Most are prefabricated in mass production and bought a large amount of electronics manufacturers. If you are a board of your own design, and not to mount with epoxy glue, you can drill holes for the screws. <br /> <p><br /> <p>1. The plate on the area you want to mount. Mark the spots where the holes are for the electronic device with a fine tip marker to adjust. <br /> <p><br /> <p>2. Insert the card into a bank in an anti-static document and press the sharp tip of a drill 1mm bullet points to an indentation on the board to make. <br /> <p><br /> <p>3. Keep the plate covered with a hand in a glove anti-static. Holes in the areas pre-marked on a board with a bit of 1mm. Do not press the weight of the drill to drill holes. <br /> <p><br /> <p>4. The fine dust from drilling PCB by means of compressed air. If so, send them right on the device where it is installed to the line of eye protection. <br />

on Jun 22, 2011 | Computers & Internet

1 Answer

China Molybdenum Plate Business Given that

This "question" is spam and has been reported as such.

Oct 18, 2013 | Thunder Tiger Pv0035t White Skids With...

1 Answer

1999 xl changed module changed coil bypassed kill switch and bank angle switch still no spark

Did you change the sensor in the timer cavity on the right side of the engine? It's behind the round plate on the cam chest cover. If still original, there are two rivets holding the cover on. Carefully drill the heads off the rivets. Do not drill any deeper than that. Once the plate comes off, you'll see the Hall effect sensor in the cavity. Mark the plate and the inside of the timer cavity so that you can remove the old plate and get a new sensor in the cavity in EXACTLY the same position. There is a plug underneath the engine that you will have to take the wires out of to get them out of the small hole. DO NOT USE STANDARD POP RIVETS TO SECURE THE PLATE BACK OVER THE TIMER CAVITY HOLE. These are special rivets that you can get from you dealership. Or, you can put an aftermarket plate that uses screws instead of rivets in the holes.

Good Luck

Sep 05, 2011 | 2000 Harley Davidson XL Sportster 883

1 Answer

I need to replace the ignition pickup on a 97 is behind the 5 logo

Yes, it is behind this plate in the timing cavity. Drill the rivet heads off so you can get the round plate off. Drill just deep enough to drill the head of the rivet off using a large drill bit. Once you get that and the other plate off, mark the original sensor plate and the inside of the timer cavity in such a manner that you can take the old sensor plate out and install the new plate in exactly the same spot. You must do this correctly or you'll have to reset the ignition timing. I usually use the very end of the slot on the plate or something like that for a reference point on the plate. Mark the inside of the timer cavity on edge. You'll also have to unpin the plug or cut the wires of the old sensor. Take the old pins out of the plug making a drawing of how the wires go into the plug, what color wire goes where. Put the wires through the hole and put the new plate in and secure the holding bolts. Repin the plug. If you put the original plate back on, you'll need new rivets. DO NOT USE STANDARD RIVETS. You must use Harley-Davidson rivets. Standard rivets will allow the broken off end to get into the timer cavity and damage the "cup" behind the plate and maybe the end of the camshaft.

Good Luck
Good Luck

Jul 15, 2011 | Harley Davidson XL 1200 C Sportster Custom...

1 Answer

I've been trying to get the oil pug out of rear axle for a good year now so I can change the gear fluid. The factory tightend it so tight that a shop with a torch to heat it cant get it out. Now the...

You could try and drill out the old plug.Start with a small drill bit then go larger.Dont get into the thread! OR if you can take the rear plate off and drill it from the inside even better because at some point the drill bit will bite the plug and remove it. You can also drill a hole in the plate a little more than half way up and tap it or use a rubber plug from the help center at the part store.I hope this helps

Jun 10, 2011 | 2004 GMC Envoy

2 Answers

Can't get to turn signal switch in steering colume have steering wheel off and down to metal plate above turnsingal switch can't get that part off

There's a special tool that is available at most part stores or tool rental stores. It's used to press down on the plate allowing it to be released.

May 23, 2011 | Chevrolet R10 Cars & Trucks

1 Answer

The Pearl BBC-1 bass drum masking plate does not fit the holes on my export bass drum

Your choices are few... get the correct plate, drill the one you have, or drill the drum.

I would opt to drill whichever part is the most replaceable which is likely the plate. Mark carefully an make sure it is square when you do so.

Feb 11, 2011 | Pearl Bass Drum Masking Plate BBC1

2 Answers

How to attach a front license plate to 2007 Highlander?

industrial grade double sided tape works, then its impossible to remove the plates again

Jan 24, 2010 | 2007 Toyota Highlander Hybrid

1 Answer

Add front license plate, do I need to remove bumper to get behind

try using self tapping screws so you dont have to remove it, you can drill pilot holes if the screw wont go thru easy, and you dont need a nut/bolt

Mar 20, 2009 | 1998 Honda CR-V

Not finding what you are looking for?
Dewalt DC920KA Heavy Duty Xrp 18V Cordless Drill/Driver Logo

Related Topics:

919 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dewalt Drills Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers


Level 3 Expert

77932 Answers

Jim Thurston

Level 3 Expert

672 Answers

Are you a Dewalt Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides