20 Most Recent Jenn-Air JJW8530C Expressions Collection Dual Single Oven - Page 2 Questions & Answers

Hi jmhostetler9,

This F3 that keeps flashing on your oven is caused by a shorted or open oven temperature sensor (RTD). To fix this problem check sensor harness and harness connection between oven sensor and oven control. Replace oven temperature sensor (RTD) if wiring is ok.You may contact Sears for the replacement part at 1-800-252-1698; M-F 6:30 AM-10:30 PM - Sat 7:00 AM-9:30 PM - Sun 7:30 AM-9:30 PM - All times Central. Just get your model # ready when you call.

Hope this helps.

Thank you for using FixYa.

One side of your 240 volt connection is disconnected, most likely in the plug wire connection. The neutral and one leg of your 240 is working thereby your display still works since it runs of 120 volts. Happened to me I had one wire come loose from stress on the plug

That noise just lets you know that the unit is on/in operation.

just finished cleaning and FC comes on and wont stay off. constant beeping

I have Jenn Air oven S136-C with a locking bar. After cleaning cycle wait for the oven to cool down and the lock light will go out (but the oven is not yet unlocked.)

Set SELECTOR knob to OFF
Set TEMPERATURE knob to CLEAN
Press CANCEL button (on right) twice.
Slide the locking bar to the left and the oven door will open

Hi,

Here is a tip that I wrote that will help figure out why the burner spark keeps on clicking...

Gas Range Repair Burners Keep on Clicking

heatman101

F1 touch pad / ERC test This simple test will help determine
whether the ERC (Electronic Range Control or Clock) or the touch pad is
defective when F1 error code is present.



Note: Some models incorporate the touch pad in to the ERC as a single
assembly, in which case this test is not necessary. Simply replace the ERC
(Clock).



Warning: If you feel in any way uncomfortable performing this test or
making this repair, please contact a qualified appliance repair technician.


1. Disconnect power to the range (unplug the range power cord or turn the power off to the range at the circuit breaker). It is very important that the power to the range has been disconnected, so please double check before continuing


2. Gain access inside the control panel.

3. Disconnect the touch pad (also called keypad or membrane switch) ribbon from the ERC


4. Make sure there are no lose wires, or anything else that may cause a short when power is turned back on. Assemble the control panel back the way it was


5. Turn the power back on.

6. Wait for at least one hour to see if the F1 code comes back (usually accompanied by a beeping sound)


7. If F1 comes back, replace the ERC. If it does not, replace the touch pad.

Hi,

Before you go working too hard to get you oven to go into the self clean mode(self destruct)....check out this tip...

Self Cleaning Oven Problem


heatman101

" Wish I had read this first. I never would have used the self cleaning option. Thanks for the info!!

Yes, the problem you are describing is most likely a fried heating element. This can be repaired for around $40

Hi,
If your electric oven is taking too long to heat or just not heating up right,then check out this tip that will give more detail about your problem.

Oven Problems Electric Oven is Heating Slowly or Poorly

heatman101

Hi, the error code implies that the Function key shorted or stuck..
You need to replace touch pad or if touch pad is part of the clock, replace the clock (ERC).

hi the only to fix it is to replace display/control jim

Hi,
Here is a tip that I wrote that will help figure out why the burner spark keepson clicking...

Gas Range RepairBurners Keep on Clicking
heatman101


hgddg

sounds like a bad keypad

Thanks for your question!

I'm sorry that you haven't received an answer yet.

The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:
1. the question is unclear, incomplete, or poorly worded...
2. the question is mis-categorized - so the correct experts aren't viewing it...
3. the question requires an answer for something that cannot be explained online adequately...
4. specific training, tools, or equipment are required to avoid injury or death...
5. the Experts that are online simply don't have the resources to answer your question fully...

Please feel free to re-work your question if you feel one of these may be the reason.
Of course you are not required - but converting your question to a PAID one usually increases the reply rate as well.

Normal rates for FixYa are...
$ 9.99 answer for one question.
$12.99 Live Real-Time online chat or premium e-mail support.
$29.99 Live Real Time phone support
Sometimes FixYa will run specials for unlimited questions via monthly subscription or reduced rates for limited periods.


Consider the savings that can be had when an informed Expert can save you a $100 service call, or a $350 trip to the car dealership.
Your problem solved - guaranteed! Or your money back!!

If you don't want to pay - feel free to re-submit your question so it returns back to the top of the work queue if you still need help.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question

This problem is likely a failure of the LCD display on the circuit board. I examined ours and it shows a burned spot inside the display unit. With our oven the display becomes visible after the oven has been on for some time. The board is simple to replace.

probably a bad oven control board. check the lock switches too while you in there messing around getting lit up lol

I have the same problem. Just swap the 2 wires that are marked as 'broil' and 'bake' on the controller board. But sometimes it switches back, then I have to swap the wires again.

You might want to leave the 'broil' post unconnected to prevent burning food..