Passanger side door will not open i know the screws to take the door panel off are on the side but can any one tell me if i can open it another way

First look for screws around the outside edge of the interior panel (side and bottom). There are two screws on the doorhandle remove these, they my be hidden by pop out caps. then locate the screw in the door opener handle area and remove it. Also remove the inside mirror cap (top right hand of door panel. Then with a small flat head screwdriver pry out the window and door lock switch and disconnectthe wiring. With a door panel removal tool or larger flathead screwdriver pry under the bottom corner of the door panel carfully, it should pop out of the door clips note: if you have a red reflector on the door at the bottom left of the panel there is a screw behind it also. Once the door panel clips pop lift up on the door panel strait up carefully and then unplug the rest of the electrical parts.Good luck

If you can't get the door open then you can't get the panel off its as simple as that, there are screws under the door card that need to be removed to gain access to the inner door workings, without getting the door open you would have to remove the wing to gain access to the hinge bolts & remove the whole door from the vehicle, then you may still have problems with the door having its mechanism locked around the door frames pin or loop

You must locate the screws that attach the door panel to the door. On some vehicles these screws are covered with some type of cap. the easiest way to find the screws is to look for places that look cut out and replaced. Another way is to look at your door upside down as it is common that the screws are located in hide-away positions.

Remove the screw by the handle that opens the door and the screw by the defrost vent. Then remove the screw that would touch the dash if the door was closed. Then remove the screw in the handle that you would use to close the door from the inside. Now remove the 2 screw at the bottom of the panel, these are kind of hard to find, runs you finger around in the carpet. Pull the plastic cover off around the opening handle, and unplug the window and lock switches. Now carefully pry off the panel. After you get the clips to release, unhook the rod from the back of the opening handle.

It is held on by 2 phillips head screws that are accessed from the inside of the door (remove the panel, remove the screws and the mirror falls down. Remove the electrical connection to the mirror motor and you are done/

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge.

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

jUST REMOVE THE SCREWS AT BOTTOM AND POP HANDLE BLANK OUT A LITTLE SO CLIP CAN BE REMOVED AT HANDLE MAKE A **** PULLER OUT OF AN OLD PUTTY KNOFE AND CUT A SLOT IN IT . bUT GOOD ENOUGH FOR KNOW .

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

the door panel has 2 small screws at the very bottom of interior panel, another 2 screws behind the pull handle<will need to be pryed apart at the seams of the pull handle, then pull out on panel to release several push clips around the panel then once panel is loose you will need to reach around the panel and disconect latch handle and electrical connectors.