Removed all the plug wires on 1998 montero sport 3.0 need to know the firing order

All in this link

3.5L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system.

Mitsubishi Montero, Sport 1998-06 Firing Orders Repair Guide

More here. Click on the images tab

https://www.google.com/search?q=2002+Mitsubishi+Montero+Sport+3.5+firing+order

..

check the firing order as you may have crossed wires . check that the HT leads are not touching each other as this will also cause you problem by causing misfiring

Here is a picture of the cylinder layout and firing order for your Montero V6 is 1 2 3 4 5 6.

Okay....since the engine size is not posted, please pick the correct one that is your engine. There will be a bunch of diagrams so pick the appropriate one:

2.4L Engine Firing order: 1-3-4-2 Distributor rotation: Counterclockwise

3.0L Engines without DIS Firing order: 1-2-3-4-5-6 Distributor rotation: Counterclockwise

Fig. 3.0L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system

Fig. 3.5L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system

Fig. 3.0L Engines without DIS Firing order: 1-2-3-4-5-6 Distributor rotation: Counterclockwise

Fig. 3.0L Engines with DIS Firing order: 1-2-3-4-5-6 Distributorless ignition system

Fig. 3.5L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system

Fig. 3.0L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system

Fig. 3.5L and 3.8L Engines Firing order: 1-2-3-4-5-6 Distributorless ignition system
Back to Top

Installing New Spark Plug Wires Is Simple, Especially Of One Wire Is Replaced At A Time. Compare The Length Of The Old Wire With The Length Of The New Wire. Replace Each Wire With One Of Equal Length.Make Sure The New Wire Is Fully Attached On The Plug And In The Distributor Or Coil Module.

Spark Plug Wire Replacement Is More Complicated If All The Wires Are Removed At Once.Then You Must Use The Engine Firing Order And Cylinder Numbers To Route Each Wire Correctly.

1998 Jeep Cherokee 4WD 4.0L MFI 6cyl

To avoid confusion, tag and remove the spark plug wires one at a time, for replacement.
If a distributor is not keyed for installation with only one orientation, it could have been removed previously and rewired. The resultant wiring would hold the correct firing order, but could change the relative placement of the plug towers in relation to the engine. For this reason it is imperative that you label all wires before disconnecting any of them. Also, before removal, compare the current wiring with the accompanying illustrations. If the current wiring does not match, make notes to reflect how your engine is wired.



Fig. 1: The firing order can usually be found cast onto the intake manifold



Fig.: 1989-98 2.5L engine Engine firing order: 1-3-4-2 Distributor rotation: Clockwise



Fig.: 2.8L engine Engine firing order: 1-2-3-4-5-6 Distributor rotation: Clockwise



Fig.: 4.0L engine Engine firing order: 1-5-3-6-2-4 Distributor rotation: Clockwise



Fig.: 5.2L and 5.9L engines Engine firing order: 1-8-4-3-6-5-7-2 Distributor rotation: Clockwise

Also, here can review the Jeep XJ Service Manual.

I hope help you with this, Good luck (remember rated this help).

4-6 or 8 cylinder. The firing order is usually casted into the ontake manifold in raised numbers. Calling Autozone or actually any friendly psrts store will get any info you need. Good Luck

autozone.com "repair info" shows:
2.4L Engine Firing order: 1-3-4-2 Distributor rotation: Counterclockwise