Question about 1992 Toyota Land Cruiser

1 Answer

Replace front turn signal bulb

Trying to replace the front directional bulb but can only find one screw on the top of the lens cover under the hood. where are the others ?

Posted by on

  • Anonymous Mar 20, 2014

    install light bulb under front hood

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Remove top screw and pull cover straight out to access bulb

Posted on Aug 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change turn signal lights


REAR UNSCREW THE UNIT PULL IT OUT TWIST THE PART THAT HOLDS THE BULB HALF A TURN PULL IT OUT REMOVE BULB REPLACE WITH SAME NUMBER BULB.

FRONT BULB CHECK TO SEE IF YOU CAN ACCESS SIGNAL FROM BEHIND UNDER THE HOOD. IF NOT REMOVE THE LENS BY REMOVING THE SCREWS AND ACCESS THE LIGHT THAT WAY. PUSH THE LIGHT BULB AND TWIST IT IT WILL POP OUTBECAUSE IT IS SPRING LOADED. ALWAYS MAKE YOU SURE YOU CHECK THE NUMBER ON THE REPLACEMENT BULB TO AVOID HAVING TO DO THE JOB TWICE/

Mar 01, 2014 | 1996 Dodge Dakota

1 Answer

Replacing a turn signal bulb....Baffled...Thanks


Hello,

Please do not be baffled. To replace the turn signal bulb on Your car is quite simple, all You need to do is to get a screwdriver and follow the steps below:
  1. Open the hood and locate the mounting screws for the outboard marker-light assembly just above the light. Remove the screws with a Phillips screwdriver, then remove the assembly, setting it aside for now.
  2. Locate the two mounting screws on top of the turn-signal light assembly under the side-marker lens. Remove the two screws with a Phillips screwdriver, then set the screws aside. Slide the turn signal out and locate the socket on the back of the assembly.
  3. Rotate the bulb socket counterclockwise and pull the socket out of the assembly. Pull the bulb straight out of the socket and discard it. Install a new bulb into the socket, pushing it in until is seats. Position the socket back into the rear of the light assembly, turn it clockwise to lock it in place, then slide the assembly back into the front of the Jeep.
  4. Install the mounting bolts that secure the turn-signal light assembly, tightening the screws with a Phillips-head screwdriver. Position the side marker-light assembly to the side of the Jeep and install the retaining bolts.
  5. Tighten the retaining bolts for the side-marker lights with a Phillips screwdriver, then close the hood. Test the repair by turning the lights on and visually verify that the light is working..
Hope this helped. Thank You for using FixYa!!!

Jan 28, 2011 | 1998 Jeep Grand Cherokee

1 Answer

Change front turn signal bulb


i have a 1990 grand am & to change the turn signal bulbs i have to opwn the hood & right over the top of the lens cover are screws that will release them. hope it works 4 ya!

Aug 27, 2010 | 1992 Pontiac Grand Am

1 Answer

Replace right front turn signal lights


Open the hood, remove the screws to the lens, pull out lens. Then take the bulb socket and turn it, then it will pull out. Then push in and turn bulb unitl it pops out so you can replace it.

Jun 24, 2010 | 1998 Toyota Tacoma

1 Answer

How do you replace the front turn signal bulb? I am having a difficult time.


turn signals are replaced one of two ways from the inside or the outside. #1 If they are replaced from the outside there will be a couple of screws on the out side of the lens take these out and the whole lens will come out turn the socket on back of lens and the bulb will be right there push bulb in and turn change bulb and reassemble. #2 you have to get at it from under the hood look from on top of signal or look up from under car you must get to the socket turn it and the bulb will be there push bulb in and turn replace bulb.

Oct 17, 2009 | 2002 Buick LeSabre

1 Answer

Replace rt. front turn signal bulb


look at the other side,under the bumper you just twist and turn and you will have access to change your bulb.

Aug 09, 2009 | 1999 Chevrolet Cavalier

1 Answer

How do I get to the front turn signal bulb to replace? From the engine compartment which doesn't sppear to be acessable or do you take off from front, removing the lense cover ???


Underneath the hood on top of the light housing is an 8mm screw and on the back side a wingnut screw, you should be able to pull this out....the hole assembly..all this located under the hood. Good Luck!

Apr 11, 2009 | 2001 Mercury Sable

1 Answer

Want to change bulb in turn signal on bottom front of driver side


If there is no screws on lens, you may have to acsess it from under car, or under hood, twist plug and should come out to chg. bulb.

Feb 13, 2009 | 2000 Buick LeSabre

2 Answers

Want to change bulb in turn signal on bottom front on driver side


UNSNAP BLACK PLASTIC UNDERNEATH FIXTURE.REACH IN AND TWIST SOCKET TO REMOVE. PULL SOCKET DOWN AND REPLACE BULB. REVERSE STEPS TO REINSTALL. THIS IS ALL DONE FROM UNDERNEATH CAR.

Feb 13, 2009 | 2000 Buick LeSabre

Not finding what you are looking for?
1992 Toyota Land Cruiser Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...