At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
Re: The remote lock will not release to exterior door on...
Is this the lever type remote you are talking about?..like inside the car?..if that is the case..it would be a cable..perhaps it needs some lube (wd40) or similar
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
push the fuel door button,if you hear the door trying to open,[or close] the cable shaft is not free. In the trunk,just behind the cap door, you will find it,spray it with a good lub. you can move this shaft with your fingers.
Jaguar 2000-06 - Locks & Lock Systems Power Door Locks - Removal & Installation
Door Lock Switch Door Lock Diagnosis & Testing
Visually inspect the following:
Misaligned door(s), hood or luggage compartment lid
Door latches
Actuating rod
Exterior door handle
Interior door handle
Door lock cylinder
Cable
Luggage compartment lid exterior release switch
Fuse(s)
Wiring harness
Electrical connector
Door lock actuator
Remote transmitter batteries
Vehicle battery
Remote transmitter
Door lock switch
Front electronic module
If an obvious cause for an observed or reported concern is found,
correct the cause (if possible) before proceeding to the next step.
Door Lock Motor Coupe And Convertible
Turn ignition key to position II.
Motor door glass to fully raised position.
Turn ignition key to position O.
Disconnect the negative battery cable.
Remove door casing for access.
Remove door water shedder.
Position PVC secondary water shedder for access.
Slacken and remove the door glass rear runner lower securing screws.
Reposition door glass rear runner. Mark the position of the glass rear runner upper securing screw.
Slacken and remove the upper securing screw and move the runner away from the glass.
Disconnect door handle and lock barrel (driver door only) operating rods from latch links.
Slacken and remove the three latch assembly securing screws and position latch for access.
Remove latch motor harness multiplug from mounting bracket and disconnect multiplug.
Release operating cable from door handle. Move inner door handle
to the locked position. Remove operating cable outer abutment from
support bracket. Disconnect cable inner from door inner handle.
Remove lock motor assembly from door.
To install, reverse removal procedure.
Fig. Removing door lock actuator
Sedan
Remove the door window glass
Detach the interior door handle.
Detach the actuator remote cable from the interior door handle.
Remove the interior door handle.
Detach the door window glass run.
Remove the exterior door handle retaining screws.
Remove the front door actuator retaining screws.
Reposition the front door actuator and exterior handle.
Remove the front door actuator and exterior handle.
Disconnect the front door actuator remote cable.
Detach the door lock cylinder connecting rod (1).
Detach the exterior door handle connecting rod (2).
Order the exterior door handle AND the clip that attaches the rod to the exterior handle from your local dealership ( any part in the salvage yard will have at least as much wear as the one U are replacing ) Also order a can of touch up paint matching your car. After you have the parts and have painted the new exterior handle, roll down the window and remove the interior door panel. ( instructions have been posted at 'replace door lock buttom' ) Two nuts, one on each side, hold the broken handle in place and must be removed ( DON'T loose them ). Loosen the rod from the clip at the top to allow a bit more room, But take note on the way it is attached ( you will need to reattach the rod to new handle ) To install new mechanism put the new clip on the rod, carefully place the gasket and the new handle in place and install nuts to secure. Test the door handle and make sure it works. Reinstall interior door panel.
×