85 Jeep Steering box.....Im trying to disconnect the steering rod from the box, and I removed bolt that goes through what looks like a clamp.......But I cant get it to come loose

Taking out the steering box in a Nissan 1400 2007 pickup truck involves a few steps, and you do not need to remove the engine to access the steering box. Here is a general guide on how to remove the steering box:
1. **Disconnect the battery**: Always disconnect the battery before working on any components in the engine bay.
2. **Raise the front of the vehicle**: Use a jack to lift the front of the vehicle and secure it with jack stands for safety.
3. **Remove the wheels**: Take off the front wheels to access the steering components.
4. **Disconnect the steering column**: Inside the cabin, detach the steering column from the steering box.
5. **Disconnect the tie rod ends**: Remove the tie rod ends connected to the steering box.
6. **Remove the steering box mounting bolts**: Locate and remove the mounting bolts that hold the steering box in place

Lock your steering wheel in place. You could run the seatbelt through it to do so. Disconnect the steering shaft front the steering box by removing the pinch bolt notice how it came out you may want to make reference marks to make sure it goes back the same way. . Disconnect the pitman arm from the center link. Disconnect the high pressure hose and return hose. You may want to drain reservoir first. The box is attached to the frame with three bolts. Remove the bolts and remove the box with the pitman at attached. Don't forget to transfer it over to new steering box noticing its position. Also make sure replacement steering box is centered prior to intallation.

use a swivel socket or look above the firewall on the inside and look for a bolt or ujoint that will undo so u can slide it up and out of the way

here hope this helps for a 98 model but very similair

1998 GMC Truck Jimmy - 4WD ' Blazer, Bravada, Jimmy, S10 Pickup, Sonoma VIN S/T Service Manual ' Steering ' Power Steering System ' Repair Instructions ' Document ID: 416283
Steering Gear Replacement (4WD) Removal Procedure Tools RequiredJ 24319-B Steering Linkage Puller
Notice: Do not rotate steering shaft after steering column has been removed. Damage to SIR components may occur.

1. Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement in Engine Controls 4.3L.




2. Place a drain pan below the steering gear.
3. Remove the inlet and the outlet hoses from the power steering gear.
Cap or tape the ends of the hoses and the gear fittings in order to prevent dirt from entering the system.




4. Remove the intermediate shaft shield from the steering gear.




5. Remove the lower intermediate shaft coupling bolt.
6. Draw alignment marks on the lower intermediate shaft coupling and the steering shaft.
7. Remove the lower intermediate shaft coupling from the steering shaft.
8. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
9. Remove the steering linkage shield. Refer to Steering Linkage Shield Replacement in Steering Linkage.




10. Remove differential carrier shield mounting bolts.
11. Remove the differential carrier shield.




12. Remove the pitman arm ball stud nut at the relay rod.




13. Disconnect pitman arm from relay rod using J 24319-B .




14. Remove the steering gear mounting bolts and the washers from the frame.
15. Remove the steering gear.
16. Remove the pitman arm. Refer to Pitman Arm Replacement in Steering Linkage.

To Remove:

1. Before servicing the vehicle, refer to the precautions at the beginning of this section. NOTE: The wheels of the vehicle must be straight ahead and the steering column in the LOCK position before disconnecting the steering column or intermediate shaft from the steering gear. Failure to do so will cause the SIR coil assembly (clock spring) to become uncentered, which may cause damage to the assembly.
   
2. Lock the steering column by installing the J42640 into the underside of the steering column.
3. Raise and support the vehicle.
4. Remove the tires and wheels.
5. Remove the power steering gear heat shield.
6. Remove or disconnect the following: CAUTION
   Failure to disconnect the intermediate shaft from the rack and pinion stub shaft can result in damage to the steering gear and/or intermediate shaft. This damage can cause loss of steering control, which could result in personal injury.
   
• Intermediate shaft lower pinch bolt and coupling from gear
• Pressure and return pipes from the gear
• Electrical connector, if equipped
  Stabilizer shaft links at lower control arms
• Remove the left stabilizer shaft insulator.
• Rotate the stabilizer shaft to access steering gear bolts.
• The outer tie rod retaining nuts.
• Using J24319-B separate the outer tie rods from the steering knuckles.
• Rack and pinion attaching bolts
• Rack and pinion assembly through the left wheel opening.
7. Transfer the outer tie rods if replacing the power steering gear.

To Install:

1. Install or connect the following:
   • Rack and pinion assembly through the left wheel opening and tighten the bolts to 70 ft. lbs. (95 Nm)
   • Electrical connector, if equipped
     Pressure and return lines to the steering gear and tighten the fittings to 22 ft. lbs. (30 Nm)
   • Heat shield and bolts. Tighten the bolts to 7 ft. Lbs. (10 N)
   • Install the left stabilizer shaft insulator.
2. Install stabilizer shaft Links to lower control arms
3. Intermediate shaft to the steering gear and tighten the pinch bolt to 35 ft. lbs. (47 Nm)
4. Install the outer tie rods to the steering knuckles.
5. Install the outer tie rods retaining nuts. torque the nuts to 22ft.lbs(30 Nm) plus an additional 180 degrees.
6. Install the tires and wheels.
7. Lower the vehicle.
8. Remove the steering column anti rotation pin from the steering column.
9. Fill and bleed the power steering system.
10. Adjust the front toe.

Lock the steering column by installing the Steering Column Anti Rotation Pin tool J 42640 into the underside of the steering column--Aurora


Steering gear mounting bolts--Aurora




Power Rack & Pinion Steering Gear Heat Shield Removal & Installation To Remove:

1. Raise and support the vehicle.
2. Remove or disconnect the following:
   • The stabilizer shaft links.
   • Rotate the stabilizer shaft downward.
   • The electrical harness clip.
   • Power steering gear heat shield mounting bolts.
   • The heat shield.

To Install:

1. Install the power steering gear heat shield.
2. Install or connect the following:
   • The mounting bolts And torque to 89in.lbs.(10 Nm)
   • The electrical harness clip.
   • Rotate the stabilizer shaft into position.
   • The stabilizer shaft links.
3. Lower the vehicle.

Figure of heat shield removed from above rack bolts with location shown

YOU HAVE TO SAFELY RAISE SUPPORT VECHICLE ON JACK STANDS.MAKE SURE YOU HAVE VECHICLE PARKED ON LEVEL SOLID GROUND.ONCE VECHICLE RAISED.REMOVE FRONT WHEELS.REMOVE TIE RODS END COTTER PINS AND CASTLE NUTS.REMOVE TIE ROD ENDS FROM THE KNUCKLES.REMOVE FRONT STABILIZER BAR.POSITION THE DASH OPENING WEATHER SEAL FOR THE STEERING COLUMN OUT OF THE WAY.REMOVE OR DISCONNECT THE FOLLOWING.REMOVE PINCH BOLT RETAINING THE STEERING COLUMN INTERMEDIATE SHAFT COUPLING.REMOVE STEERING GEAR RETAINING NUTS BOLTS.REMOVE REAR SUBFRAME BOLTS.USE WIRE TO SUPPORT EXHAUST COMPONENTS UNLESS YOU ARE REMOVING THEM COMPLETELY.SUPPORT THE EXHAUST SYSTEM FLEX TUBE AND REMOVE THE FLEX TUBE TO DUAL CONVERTER Y PIPE ATTACHMENT.LOWER THE VECHICLE SLIGHTLY UNTIL THE REAR SUBFRAME SEPARATES FROM THE BODY APPROXIMATELY 4 INCHES.REMOVE THE HEAT SHIELD BAND AND FOLD THE HEAT SHIELD DOWN.ROTATE THE RACK AND PINION ASSEMBLY TO CLEAR THE BOLTS FROM THE FRONT SUBFRAME AND PULL TOWARD THE DRIVERS SIDE OF THE VECHICLE.PLACE A DRAIN PAN UNDER THE VECHICLE AND DISCONNECT THE POWER STEERING LINES.REMOVE THE RACK AND PINION ASSEMBLY THROUGH THE DRIVERS SIDE OF THE VECHICLE***** TO INSTALL ****** INSTALL NEW TEFLON O - RINGS ON THE POWER STEERING LINE FITTINGS. PLACE THE RACK AND PINION RETAINING BOLTS IN THE GEAR HOUSING.INSTALL RACK AND PINION ASSEMBLY THROUGH THE DRIVERS SIDE OF THE VECHICLE.INSTALL POWER STEERING LINES ON THE RACK AND PINION ASSEMBLY. INSTALL RACK AND PINION ASSEMBLY ON THE SUBFRAME.INSTALL ******** HEAT SHIELD.INSTALL TIE ROD ENDS TO THE KNUCKLES TIGHTEN THE CASTLE NUTS AND INSTALL THE COTTER PINS.INSTALL STABILIZER BAR.INSTALL RACK AND PINION ASSEMBLY RETAINING BOLTS.TORQUE THEM TO 85 - 99 FT LBS. RAISE VECHICLE UNTIL SUBFRAME CONTACTS THE BODY.INSTALL REAR SUBFRAME RETAINING BOLTS TORQUE THEM TO 83 - 112 FT LBS.INSTALL EXHAUST SYSTEM FLEX TUBE TO DUAL CONVERTER Y PIPE.INSTALL FRONT WHEELS.INSTALL A NEW PINCH BOLT IN THE STEERING COLUMN INTERMEDIATE SHAFT COUPLING ON THE RACK INPUT SHAFT TORQUE PINCH BOLT TO 25 - 33 FT LBS.POSITION THE STEERING COLUMN OPENING WEATHER SEAL OVER THE STEERING GEAR HOUSING.LOWER THE VECHICLE FILL THE POWER STEERING FLUID RESERVOIR. START THE VECHICLE AND CHECK FOR LEAKS. CHECK FOR PROPER WHEEL ALIGNMENT AND STEERING WHEEL POSITION.BLEED POWER STEERING SYSTEM.

Copied from AutoZone.com:

1. Before servicing the vehicle, refer to the Precautions Section.
2. Turn the steering wheel to the straight ahead position and remove the key from the ignition.
3. Turn the wheel counterclockwise in order to lock the steering column in place.
4. Raise and support the vehicle.
5. Remove the front wheels.
   WARNING Do not rotate the intermediate shaft once separated from the gear. Possible damage or a malfunction could occur.
   
   
   Fig. Steering shaft pinch bolt
   
   
   Fig. Steering gear mounting
   
6. Remove the steering gear to intermediate shaft pinch bolt and discard.
7. Disconnect the intermediate shaft from the steering gear.
8. Remove both steering gear outer tie rod to knuckle nuts and discard the nuts.
   WARNING Do not attempt to separate the joint using a wedge type tool.
   
9. Separate the outer tie rods from the steering knuckles.
10. Remove the steering gear bolts.
11. Remove the rear transaxle mount.
12. Carefully remove the steering gear from the frame and the vehicle through the LH wheel opening.

To install:

1. Install the steering gear to the frame through the LH wheel opening.
2. Install the steering gear bolts. Tighten the bolts to 81 ft. lbs. (110 Nm).
3. Install the rear transaxle mount. Tighten the rear transaxle mount to frame bolts. Tighten the bolts to 44 ft. lbs. (60 Nm).
4. Tighten the rear transaxle mount thru bolt. Tighten the thru bolt to 74 ft. lbs. (100 Nm).
5. Connect the intermediate shaft to the steering gear.
6. Install a new intermediate shaft pinch bolt. Tighten the bolts to 25 ft. lbs. (34 Nm).
7. Install the outer tie rods to the steering knuckles.
8. Install new outer tie rod nuts. Tighten the bolts to 44 ft. lbs. (60 Nm).
9. Install the front wheels.
10. Lower the vehicle.
11. Adjust the toe if necessary.

this is for 1996, don't have 89.
these may be steps you need

1. Remove pinch bolt from steering shaft flex coupling.
   

1. Disconnect shift cable from selector lever pivot.
   

1. Remove shift cable from steering column lower mounting bracket by pushing tab on cable in and sliding cable off bracket.
   

1. Disconnect ignition switch (11572) by loosening bolt and removing connector. The bolt is part of connector and can not be removed.
   

1. While supporting steering column, remove four retaining nuts.
   

1. Disconnect collapsible intermediate shaft from U-joint at lower end of steering column.
   

1. Remove steering column from vehicle.
   

you can buy remanufactured at parts store or buy used from car-part.com. page with * is lowest cost.

It's a pretty big job for a novice.

here's 96 taurus steps with 3.8l engine. don't have 94. should be similar

Removal
SPECIAL SERVICE TOOL(S) REQUIRED Tool Number Description T94T-6000-AH Exhaust Connector Holder Tool T57L-500-B Bench Mounted Holding Fixture

1. Disconnect negative battery cable.
   

1. Position steering wheel one-half turn to right and lock wheel.
   

1. Position steering column boot out of the way. Remove pinch bolt retaining steering column intermediate shaft coupling to power steering short rack and separate.
   

1. Disconnect PCV vent tube and vacuum supply hose from clean air tube. Loosen two hose clamps retaining clean air tube and position out of the way.
   

1. Disconnect power steering auxiliary actuator and power steering pressure switch.
   

1. Remove two heat shield pushpin retainers from power steering hose bracket and remove heat shield.
   

1. Remove one retaining bolt from left turn pressure hose bracket.
   

1. Position drain pan under steering gear.
   

1. Remove power steering pressure and return hoses from fittings on power steering rack. Position both hoses out of the way. Disconnect rear HO2S connector at steering rack and position out of the way.
   

1. Partially raise vehicle.
   

1. Remove front wheel and tire assemblies.
   

1. Remove LH upper stabilizer bar link retaining nut and position link out of the way.
   

1. Loosen LH tie-rod jam nut. Remove cotter pin and tie-rod retaining nut at lower control arm. Using tie-rod end separator or equivalent, remove tie-rod from control arm and from steering gear.
   

1. Loosen RH tie-rod jam nut. Remove cotter pin and tie-rod retaining nut at lower control arm. Using tie-rod end separator or equivalent, remove tie-rod from control arm and from steering gear.
   

1. Raise vehicle.
   

1. Remove drain pan.
   

1. Remove two steering gear retaining nuts at front subframe.
   

1. Install Exhaust Connector Holder Tool T94T-6000-AH on flex tube.
   

1. Remove bolts, nuts, and gasket from where flex tube and converter Y-pipe connect. Separate tube from pipe.
   

1. Position Rotunda Power Train Lift 014-00765 or equivalent with wood blocks approximately 1016 mm (40 inches) in length (secured to lift) under subframe and raise.
   

1. Remove two rear subframe retaining bolts and lower subframe approximately 102 mm (4 inches).
   

1. Rotate power steering rack to clear bolts from subframe and remove assembly through LH wheel well.
   

1. Remove two bolts retaining power steering hose bracket to short rack and remove bracket.
   

1. Mount steering gear assembly in Bench Mounted Holding Fixture T57L-500-B.
   

1. Remove four clamps retaining bellows to steering gear and tie-rods. Remove bellows and power steering gear rack tube.
   

1. Position rack and pinion steering gear so several steering gear teeth are exposed. Hold steering gear with adjustable wrench on end teeth only, while loosening inner tie-rods. Remove tie-rods from steering rack. Remove steering rack from bench-mounted holding fixture.
   

Installation

1. Mount new steering gear assembly in Bench Mounted Holding Fixture T57L-500-B.
   

1. Position rack and pinion steering gear so several steering gear teeth are exposed. Hold steering gear with adjustable wrench on end teeth only, while tightening inner tie-rods. Tighten to 90-110 Nm (66-81 lb-ft).
   

1. Apply Steering Gear Grease C3AZ-19518-A meeting Ford specification ESB-M1C119-A to groove in connecting rods where tie-rod bellows clamp to front wheel spindle tie-rod and uniformly apply to inner diameter of bellows. Install bellows and gear rack tube onto short rack.
   

1. Install new inner and outer bellows clamps.
   

1. Remove steering gear from Bench Mounted Holding Fixture and place on bench.
   

1. Install power steering hose bracket and retaining bolts at top of steering gear. Tighten to 9-12 Nm (80-106 lb-in).
   

1. Install steering gear retaining bolts in steering gear housing and install short rack through LH wheel well.
   

1. Position steering rack and retaining bolts through subframe. Raise powertrain lift until rear subframe contacts body and install retaining bolts. Tighten to 135-195 Nm (100-144 lb-ft). Lower and remove powertrain lift from vehicle.
   

1. Install power steering short rack-to-subframe nuts. Tighten to 97-132 Nm (72-97 lb-ft).
   

1. Install new gasket, bolts and nuts at converter Y-pipe and flex tube. Tighten to 34-46 Nm (26-34 lb-ft).
   

1. Remove flex tube holder.
   

1. Partially lower vehicle.
   

1. Install LH jam nut and outer tie-rod to inner tie-rod. Install tie-rod to steering knuckle. Install retaining nut. Tighten to 47-63 Nm (35-46 lb-ft). Install new cotter pin.
   

1. Install LH stabilizer bar link and retaining nut. Tighten to 76.5-103.5 Nm (57-76 lb-ft).
   

1. Install RH jam nut and outer tie-rod to inner tie-rod. Install tie-rod to steering knuckle. Install retaining nut. Tighten to 47-63 Nm (35-46 lb-ft). Install new cotter pin.
   

1. Install tire and wheel assemblies. Tighten to 115-142 Nm (85-105 lb-ft).
   

1. Lower vehicle.
   

1. Remove old Teflon® O-rings from pressure and return hoses. Install new Teflon® O-rings on pressure and return hoses.
   

1. Install power steering pressure hose and return hose to fittings on power steering short rack. Tighten to 33-41 Nm (24-30 lb-ft).
   

1. Install one retaining bolt to left-turn pressure hose bracket. Tighten to 9-12 Nm (80-106 lb-in).
   

1. Connect rear HO2S connectors, power steering auxiliary actuator, and power steering pressure switch electrical connectors.
   

1. Position heat shield at power steering hose bracket and install pushpin retainers.
   

1. Install clean air tube, connect PCV vent tube and vacuum supply hose, and tighten hose clamps. Tighten to 2-3 Nm (18-27 lb-in).
   

1. Install steering column intermediate shaft coupling to power steering short rack and install pinch bolt. Tighten to 41-51 Nm (30-38 lb-ft). Position steering column boot over steering rack.
   

1. Fill and purge system.
   

1. Check operation.
   

1. Adjust only toe for alignment. Refer to Section 04-00 .
   

if fluid is flowing out the bellows, you need to replace the steering rack assembly. There is no fluid in the area of the inner tie rod. The seal is just before the tie rod.

Steering Gear
The power rack and pinion steering gear is serviced as a power steering short rack (3L547). The front wheel spindle tie rods (3280) and tie rod ends (3A130) are serviced individually. -------------------------------------------------------------------------------------------

• The power rack and pinion steering gear incorporates quick connect fittings for the power steering pressure hose (3A719) and power steering return hose (3A713) that allow the lines to swivel. This is normal and does not indicate loose fittings.
• If the fittings leak, check to make sure they are tightened to 14-20 Nm (10-14 lb-ft). Do not overtighten.
• If the leak is not corrected, replace the fitting seals.

-------------------------------------------------------------

-----------------------------------------------------
Section 11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Tie Rod End Steering Gear Installed
Removal

1. Remove and discard cotter pin and nut from worn tie rod end (3A130).
   

1. Disconnect tie rod end from front wheel knuckle (3K185), using Tie Rod End Remover TOOL-3290-D or equivalent.
   

1. Hold tie rod end with a wrench and loosen tie rod end jam nut.
   

1. Note depth to which tie rod end was located by using the jam nut as a marker. Grip tie rod end with a pair of suitable pliers and remove tie rod end from front wheel spindle tie rod (3280).
   

---------------------------------------------------------------------------------------
11-02: Steering System, Power 1997 Windstar Workshop Manual
REMOVAL AND INSTALLATION Steering Gear Removal

1. Raise vehicle on a twin post hoist and remove wheel and tire assemblies. Refer to Section 00-02 .
   
   
   
   
   

1. Support vehicle with jackstands under front jack pads.
   

1. Remove tie-rod end cotter pins and nuts and remove tie rod ends (3A130) from front wheel knuckle (3K185). Refer to Section 04-01 .
   

1. Remove front stabilizer bar (5482). Refer to Section 04-01 .
   

1. Disconnect heated oxygen and catalyst monitor sensors.
   

1. Support flex pipe.
   

1. Remove bolts and disconnect flex pipe from the converter.
   

1. Raise dash opening steering column opening weather seal (3513) (secondary) above the steering gear housing (3548).
   

1. Remove pinch bolt retaining steering column intermediate shaft coupling (3A525) to power steering gear input shaft and control (3D517) and disconnect the shaft.
   

1. Remove nuts from steering gear-to-front subframe retaining bolts. Remove bolts.
   

1. Remove rear subframe-to-body retaining bolts.
   

1. Lower twin post hoist carefully until rear of subframe (5R003) separates from body, approximately four inches.
   

1. Remove heat shield band and fold shield down.
   

1. Rotate power rack and pinion steering gear to clear bolts from front subframe (5C145) and pull left to facilitate line fitting removal.
   

1. Place a drain pan under vehicle and remove line fittings.
   

1. Remove power rack and pinion steering gear through LH wheel well.
   

1. Remove and discard the O-rings.
   

Installation

1. Install new Teflon® O-rings on line fittings as outlined.
   

1. Place steering gear retaining bolts in steering gear housing.
   

1. Install power rack and pinion steering gear through LH wheel well.
   

1. Install power steering line fittings to power rack and pinion steering gear.
   

1. Position power rack and pinion steering gear into front subframe.
   

1. Install ******** heat shield.
   

1. Install tie-rod ends to front wheel knuckle. Install nuts and new cotter pins. Refer to Section 04-01 .
   

1. Install LH front stabilizer bar. Refer to Section 04-01 .
   

1. Install steering gear to subframe mounting nuts. Tighten to 115-135 Nm (85-99 lb-ft).
   

1. Raise hoist until rear subframe contacts body.
   

1. Install rear subframe to body retaining bolts. Tighten to 113-153 Nm (83-112 lb-ft).
   

1. Install exhaust system flex tube to dual converter Y pipe (5F250) and remove flex tube support.
   

1. Connect heated oxygen and catalyst monitor sensors.
   

1. Install tire and wheel assemblies. Tighten lug nuts (1012) to 115-142 Nm (85-104 lb-ft).
   

1. Using a new pinch bolt, install the steering column intermediate shaft coupling on the power steering gear input shaft and control and the lower steering column shaft. Tighten the pinch bolt to 34-46 Nm (25-33 lb-ft).
   

1. Position steering column opening weather seal (secondary) over the steering gear housing. Tighten nuts to 4.5-6.3 Nm (40-55 lb-in).
   

1. Remove jackstands and lower vehicle.
   

1. Fill power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent meeting Ford specification ESW-M2C33-F. Refer to Section 11-00 .
   

1. Check system for leaks and proper operation.