How do i take off the driver side door panel - 2000 Chevrolet S-10

You have 3 screws on the buttom panel and some push pins after remouving screws just pull and it will come of then 3 bolts for your miror

First disconnect negative battery terminal.Underneath of armrest there is two screws, remove them, using small screw driver pry out armrest switch control plate and remove screw behind it, pry of the side mirror cover using wide putty knife. carefully start prying from the bottom of the door around going toward the top then lift the door panel over door lock knob. Carefully look under and disconnect all electrical connectors and remove the panel. Installation is in reverse order of removal!

Check driver side switch panel both sides control from switches,,,, both sides of dash with doors open there is a triangle area panel fuse on driver side and connectors for door electrics,, on passenger side the connectors for passenger side check connections..

Trim and molding remove tool and a phillips screw driver
Drivers Side

Remove
Door trim panel and water shield (top where window is)
Plastic panel around door handle. snaps out
1 screw upper front extension assembly (plastic triangle)
2 screws located lower bottom left (drivers side) and door trim panel
Use remove tool to push out retaining 'C' clip behind door handle
Grasp panel where opening are and pull up and out gently
Now disconnect wire harness

There two common problems with the driver's door control panel, rain water gets into the module and damages the electrics or the wires in the door boot break or abrade and short out. To check out the control panel itself, take the passenger side panel and hook it up to the drivers side, if everything works, replace the driver's panel.

Instrument Panel Fuse Block
The instrument panel fuse block access door is
located on the driver side edge of the instrument panel.

Pull off the cover to access the fuse block.

The vehicle may not use all of the fuses shown.

Fuses Usage
1 Rear Seats
2 Rear Accessory Power Outlet
3 Steering Wheel Controls Back light
4 Driver Door Module
5 Dome Lamps, Driver Side Turn Signal
6 Driver Side Turn Signal, Stop lamp
7 Instrument Panel Back Lighting
8 Passenger Side Turn Signal, Stop lamp
9 Passenger Door Module, Driver Unlock
10 Power Door Lock 2 (Unlock Feature)
11 Power Door Lock 2 (Lock Feature)
12 Stop lamps, Centre High Mounted Stop lamp
13 Rear Climate Controls
14 Power Mirror
15 Body Control Module (BCM)
16 Accessory Power Outlets
17 Interior Lamps
18 Power Door Lock 1 (Unlock Feature)
19 Rear Seat Entertainment
20 Ultrasonic Rear Parking Assist, Power Liftgate
21 Power Door Lock 1 (Lock Feature)
22 Driver Information Centre (DIC)
23 Rear Wiper
24 Cooled Seats
25 Driver Seat Module, Remote Key less Entry System
26 Driver Power Door Lock (Unlock Feature)

Front Door Panel - Town Car - Removal
CAUTION: To avoid breakage of door pull cover(s), insert a screwdriver diagonally between pull strap and chrome bracket. Snap out both sides then remove.

Snap out two door pull strap retaining screw covers. Remove screws.

Remove two screws on front and rear side of front door trim panel.
The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.
Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.

NOTE: Do not use front door trim panel (23942) to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.

Remove window regulator control switch housing from back of front door trim panel . Lift up housing, remove retaining screws and disconnect all connectors.

Disconnect driver seat regulator control processor switch (driver door only) if equipped.
Twist out interior lamp wire assembly and remove the front door trim panel.
Installation

Ensure plastic watershield is secured to door panel.
Position front door trim panel to door. Connect interior lamp wiring.
Position the window regulator control switch housing and connect switch connectors. Install the retaining screws.
Connect driver seat regulator control processor (14C708) (driver door only) if equipped.
Align door lock side to its mating slide on the sheet metal (front doors only).
Snap in front door trim panel. Ensure all retainers fit properly.
Install two retaining screws on front and rear side of front door trim panel .
Install two retaining screws and pull strap covers.

Good luck Remember rated this).

how do i replace the side mirror on 94 acura integra

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door