I REPLACED THE PCM ON MY 2008 FORD TAURUS NOW I GET A CODE 23 ON MY ANTI THEFT SYSTEM CAN I RESET IT.

You can't just change parts an expect it to work , software , modules won't let it work . You have to take it to the dealer or have a mobile lock smith fix it , reprogram it ETC...
Anti-Theft -Passive Anti-Theft System (PATS) The passive anti-theft system (PATS) contains the following components:

• theft indicator
• encoded ignition key
• PATS transceiver module
• powertrain control module (PCM)
• standard corporate protocol (SCP) communication network
• Passive Anti-Theft System (PATS) -Diagnostic Trouble Codes (DTC) Index Powertrain Control Module Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1213 Anti-Theft Number of Programmed Keys is Below Minimum PCM GO to Pinpoint Test F . B2431 Transponder Program Failure PCM VERIFY if using correct PATS key, if defective USE new key. B1342 ECU is Defective (EEFROM in PCM not working) PCM INSTALL a new PCM. REFER to Section 303-14 . B2103 Antenna Not Connected PCM GO to Pinpoint Test A . B1600 PATS Ignition Key Transponder Signal is Not Received PCM GO to Pinpoint Test B . B1601 PATS Received Incorrect Key-Code From Ignition Key Transponder PCM GO to Pinpoint Test C . B1602 PATS Received Invalid Format of Key-Code From Ignition Key Transponder PCM GO to Pinpoint Test D . B1681 PATS Transceiver Module Signal is Not Received PCM GO to Pinpoint Test E . - All Other DTCs PCM REFER to Section 419-10 .

Try pulling the fuse for the anti theft system and starting. If the car starts normally, then the problem is with the theft system. The theft system will reset itself after a period of time.

Can I reset anti-theft ???? Not unless you have a $3,000 factory scanner . Your best bet , have it towed to the dealer

https://itstillruns.com/reset-antitheft-2008-ford-taurus-7615782.html


Thought It Was Dead But It Just Won Start

You don't reset anti-theft systems ! Your ford has the PATS - passive anti-theft system ! Is the red light on top of the instrument panel flashing when trying to start the vehicle ? Need to see what DTC'S - diagnostic trouble codes are stored , fix the problem !

The PATS - passive anti-theft system is a program (software ) programmed into the instrument cluster , PCM - engine computer , GEM module etc... Plus behind the plastic shroud on steering column where the lock cylinder is located the passive anti-theft transceiver module ! You better know what your getting into when you start to mess with anti-theft systems , you can render your vehicle useless if your not careful ! Need factory scanner to program keys , to read trouble codes , check data etc... If you change transceiver module it will need to be programmed ! FORD DEALER ONLY ! You can program more keys but need to have original two keys that came with the vehicle or you can't do it >
Passive Anti-Theft System (PATS) -Principles of Operation PATS uses a specially encoded ignition key. Each encoded ignition key contains a permanently installed electronic device called a transponder. Each transponder contains a unique electronic identification code out of over 18 billion, billion combinations.
The passive anti-theft system (PATS), also known as SecuriLock ®, uses radio frequency identification technology to deter a drive-away theft. This system is known as SecuriLock® in North America, Safeguard® in the U.K., and PATS in Continental Europe. Passive means that it does not require any activity from the user.
The SecuriLock® System (PATS) is not compatible with non-Ford aftermarket remote start systems, which allow the vehicle to be started from outside the vehicle. These systems may reduce the vehicle security level, and also may cause no-start issues. If equipped, the remote start system must be removed before investigation of PATS-related, no-start issues.
Each encoded ignition key must be programmed into the vehicle powertrain control module (PCM) before it can be used to start the engine. There are special diagnostic repair procedures described in this section that must be carried out if a new encoded ignition key is necessary.
The correct ignition key is a different design than prior model years. Please consult the Rotunda Key Ordering Guide for the correct part number.
So , before messing with something you know nothing about , do yourself a favor , take it to the nearest FORD dealer !
So

Bobby, Ford Taurus anti theft system reset procedure. reset button below driver side dash. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
How do you reset securiLock anti theft system on 2003 Ford Taurus
How do disarm anti theft device on 2001 ford taurus
https://answers.yahoo.com/question/index?qid=20081101221926AAKSS8V

The passive vehicle protection system will be activated and will disable the vehicle from starting if there is a:

• damaged encoded key.
• unprogrammed key.
• non-encoded key (key has no electronics).
• wiring concern.
• transceiver concern.
• PCM concern.
• module communications network concern.

Reset ? IF your anti-theft system light is flashing when trying to start your vehicle , an the engine doesn't crank , turn , or nothing happens when you turn key , then your anti theft system is at fault ! An trying to reset will not work ,you need to have it checked DTC'S - diagnostic trouble codes ,then fixed ! I suggest you have it towed to the dealer or a ASE certified repair shop !
PATS uses the powertrain control module (PCM) to enable or disable the engine. The PATS module communicates with the PCM over the SCP communication network in order to enable engine operation. The PATS module and the PCM use sophisticated messages in order to prevent a theft. The PATS and the PCM share security data when first installed together, making them a matched pair. After this security data sharing, these modules will not function in other vehicles. The PCM shared security ID is remembered even if the battery is disconnected. The PATS module also stores the vehicle's key identification code, even if the battery is disconnected. There are special diagnostic repair procedures outlined in this workshop manual that may be carried out if either the PATS module or the PCM needs replacement.

Hi Carol , do you mean PATS passive antitheft system ? Locked up your car ,do you mean it won't crank over an start ?
The passive anti-theft system uses radio frequency identification technology to deter a driveaway theft. Passive means that it does not require any activity from the user.

• During each vehicle start sequence, the ignition key identification code is requested by the vehicle protection anti-theft electronics.
• If the key's ID code has been programmed into the system, the powertrain control module (PCM) (12A650) is signaled to enable the vehicle to start.
• If the key's ID code is not programmed into the system, or if no encoded key is detected, then the powertrain control module is signaled to disable the vehicle.

The passive anti-theft system communicates the state of the security system to the powertrain control module via the J-1850 communications network data link connector (DLC). The powertrain control modulebased on the communications from the passive anti-theft system, will determine if the vehicle's engine is enabled to start. The passive anti-theft system differs from the active anti-theft alarm system in that the passive anti-theft system enables/disables the vehicle from starting and only operates with the ignition switch in RUN/START position. The active anti-theft alarm system has perimeter protection capabilities and operates only with the ignition switch OFF. Refer to Section 13-11A for active anti-theft alarm system information.
Vehicle Disabling The passive anti-theft system will be activated and disable the vehicle from starting if any of the following conditions exist:

• damaged encoded key
• unprogrammed key
• non-encoded key (key has no electronics)
• wiring concern
• transceiver concern
• Passive Anti-Theft System (PATS) control module concern
• J-1850 Communications Network concern
• Powertrain Control Module (PCM)

replacing battery more likely erase ECM memory.best to start vechicle let enginet idle until ECM relearn memory.your vechicle has to complete full drive cycle before ECM MEMORY return if not let dealership reset engine idle.