Cars & Trucks Logo

Related Topics:

A
Anonymous Posted on Sep 08, 2017

Hi, my Ssangyong Musso 2.9L diesel is leaking engine water from inside the clutch arm (clutch slave cylinder pushes on it). Does any body have advise on how to fix please?

This water is inside the bell housing. The flow increases when the car is on ON or running. It happened while I was driving, smelt something then checked temperature and it was heading to the red. Switched engine of in emmedialtely. The engine is still turning over.

5 Related Answers

bfg3

  • 51 Answers
  • Posted on Jan 12, 2009

SOURCE: clutch cylinder inside car is it broke

you have to bleed the air out of it. If there is not fluid leaking from the master cylinder on the firewall.it can leak on the inside of car or the out side if the master cylinder is bad.first make sure the reservoir stays full then open the bleeder on slave cylinder. this is called gravity bleeding. once fluid comes out, tighten bleeder, pump pedal one time loosen bleeder while holding clutch pedal down and then tighten. do this repeatedly until no air comes out. you can pump pedal several times,then hold and bleed however you like but I have better luck with individual pumps. just make sure that the lines hooked to slave cylinder are tight and there are no air leaks. and that the line does not go below the slave cylinder because sometimes air gets trapped in the lowest part of system.

Ad

Anonymous

  • 6784 Answers
  • Posted on Mar 13, 2009

SOURCE: 2000 Sunfire coolant problem. Engine overheating,

ok, its time for a radiator flush. there is major sludge in the internals of this radiator. Make sure the thermostat is in the correct position as well. I've seen many cars come into my shop with the thermostat inserted backwards.

Anonymous

  • 6982 Answers
  • Posted on May 30, 2009

SOURCE: leaking clutch fluid Where is the slave cylinder"..I have been told to look at the slave cylinder because I do not see fluid under the car.

Slave cylinder should be on the left side of the bellhousing (follow the line from the clutch master if necessary) If you don't see fluid but you have lost some, also check where the rod from the pedal goes through the firewall to the master...they often leak there and will not drip on the ground.

Martin Bergin

  • 133 Answers
  • Posted on Mar 03, 2010

SOURCE: 1992 Chevy Silverado - Clutch Slave Cylinder broke

JB weld will not work get it welded by a pro with the proper hi frequency welder otherwise you will have to replace the box ,and yes get a new cylinder ,hope you get sorted

Anonymous

  • 1 Answer
  • Posted on Jul 04, 2010

SOURCE: 1997 Ssangyong Musso engine has erradic idle & intermittent start

i think the problem is in the fuel line. i have encounter it too.. the best way is to replace all fuel filter. muzzo have 3 fuel filter. 2 located at the engine and the other one located at the fuel tank they called it as strainer. u can see the opening of the tank underneath the back seat of the car. also good suggestion clean the tank. duel dirt is the main cause of your problem cause muzzo have only a small tip that why only little dirt can cause plunging in engine. sory for bad English

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

2005/6 Hyundai Tucson. Why is the slave cylinder arm lever fully extended?

It sounds like something not put back correctly or adjusted. Was the slave cylinder arm push in when you bled the system? There may be air behind it. Did you use a pressure bleed system, slave up to Master. Lots of help in the links.

https://www.google.com/search?q=2005+6+hyundai+tucson+clutch+master+cylinder+replacement

https://www.google.com/search?q=2005+6+hyundai+tucson+clutch+adjustment

0helpful
1answer

I have a 2006 ssangyong musso diesel engine it will not start

There are several possible reasons why a 2006 Ssangyong Musso with a diesel engine might not start, even if the engine is cranking over. Some possible causes could include:
  1. A problem with the fuel system, such as a clogged fuel filter or a malfunctioning fuel pump
  2. A problem with the ignition system, such as a faulty spark plug or a malfunctioning ignition coil
  3. A problem with the engine itself, such as a seized piston or a damaged cylinder head
  4. A problem with the electrical system, such as a dead battery or a faulty starter motor
To diagnose the problem and determine the necessary repairs, it is best to have a mechanic inspect the car and perform any necessary tests. They may need to check the condition of the fuel system, the ignition system, the engine, and the electrical system, and they may use diagnostic equipment to read any fault codes stored in the car's computer system. Based on the results of the inspection and testing, the mechanic should be able to determine the cause of the problem and recommend the appropriate repairs.
1helpful
1answer

Hi- 1995 jeep wrangler 2.5yj- clutch grinding won't go into gear - seems full of fluid but over filled it works good for a few months -does it again- repeated -works good-maybe master slave problem ?

1995 YJ if still stock all that is ONE PART, see FSM quote below.
is the fluid dropping, day by day, week by week???
y/n?
yes, then either the slave or mc are bad.
sometimes both can fail, (rust happens inside and is progressive)
what I do , is this. (if not wanting to change out both)
1: look at the MC, if it done leak down either side of the fire wall
it might be good (dont mean the piston seals good but its not leaking, so if fluid drops , (every week say) the the MC is ok
and for sure the slave leaks.

2: so where is your slave. have you looked,? (swaps happen)
most leak and can not be detected as that leak landed on the road to work.
for sure its just 2 parts, here, you know the clutch is ok.
because it works with fluid in the system and bled.
now ILL PASTE THE FSM words out of a real factory service manual.
they are clear.
FSM words, QUOTE:
CLUTCH HYDRAULIC LINKAGE REMOVAL
The clutch master cylinder, slave cylinder
and connecting line are serviced as an assembly
only.
The linkage components cannot be
overhauled or serviced separately. The cylinders
and connecting line are sealed units. Also
note that removal/installation procedures for
right and left hand drive models are basically
the same. Only master cylinder location is different.
(1) Raise vehicle.
(2) Remove fasteners attaching slave cylinder to
clutch housing.
(3) Remove slave cylinder from clutch housing (Fig.
9).
(4) Disengage clutch fluid line from body clips.
(5) Lower vehicle.
(6) Verify that cap on clutch master cylinder reservoir
is tight. This is necessary to avoid undue spillage
during removal.
(7) Remove clutch master cylinder attaching nuts.
Note that one nut is accessible from engine compartment
and one nut is accessible from under instrument
panel (Figs. 10 and 11).
(8) Remove clip securing clutch master cylinder
push rod to pedal and slide push rod off pedal pin.
(9) Disconnect clutch pedal position switch wires.
(10) If pedal pin is equipped with bushing, inspect
condition of bushing and replace it if worn or damaged.
(11) Remove clutch hydraulic linkage through engine
compartment.
0helpful
1answer

Ssangyong musso. 2005 2.9 diesel. turbo. hard to

turbo seal is blown allowing oil into air intake charge-white/blue smoke=oil- black smoke=rich fuel mix-replace turbo-cheers Denny
0helpful
1answer

Diesel fuel water in sangyong musso

Install a water-fuel serperator and drain it reguarly
0helpful
1answer

Ssangyong 2005 model Musso sport 4 x4 won't start

SSANGYONG 4x4 wheel drive discussion forum - 4x4rum.co.uk

www.4x4rum.co.uk/forum-section.php?manufacturer=SSANGYONG...

4 days ago - 50 posts - ‎23 authors
I have a Musso with a speedo that under reads by 20 % I have changed the complete ..... I have Ssangyong Actyon Sports, 4x4 2008 model.

Ssangyong 2005 model Musso sport 4 x4 won't start - Fixya

www.fixya.com/.../t11645560-ssangyong_2005_model_musso_sport_4...
Feb 11, 2012 - Ssangyong 2005 ... hello there you in wrong section of this forum proporsche.

2004-2006 SsangYong Musso - ProductReview.com.au

www.productreview.com.au > Cars > Utes > SsangYong

2004-2006 SsangYong Musso Questions & Answers ...

www.productreview.com.au > ... > 2004-2006 SsangYong Musso
When cold the transmission won't go into 4th gear then when it does it won't ... My2005 diesel 2.9 4/4 starts ist thing every morning but not so when engine is ... My 2007musso sports 4x4 will go into low range but not engage 4wd any advice?
0helpful
2answers

The clutch is stuck to the floor bord and i cant shift

you may have a faulty clutch master cylinder or faulty clutch slave cylinder- leaking clutch fluid. most of the time both are replaced at the same time which should be recomended by your mechanic, the bolts to the master cylinder are very hard to get to and require the right tool.
you should be able to move car forward by selecting 1st then cranking engine till it starts, gear changes while driving are hard but not impossible. i recommend a tow truck to a local repairer.
Not finding what you are looking for?

171 views

Ask a Question

Usually answered in minutes!

Top SsangYong Experts

jws1013

Level 3 Expert

1713 Answers

Ngoro

Level 3 Expert

3523 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a SsangYong Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...