Question about Dodge Cars & Trucks

Open Question

Changing water pump 09 dodge 3.5 6 cylinder journe y

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 176 Answers

SOURCE: water pump 1996 dodge ram van 318 2500

Before you remove the serp belt, loosen the clutch fan bolts from the water pump. Other wise you will be fighting with them later. Other wise just drain the coolant and remove the pump. I would suggest a new thermostat since the coolant is drained. Make sure the block surface is cleaned of all gasket material and other dirt before installing your new pump. I usually scrape the area with a putty knife and wipe it down with some brake clean on a rag.

Posted on May 20, 2009

  • 5 Answers

SOURCE: What's the steps if changing water pump for a

I suggest getting the Haynes service manual for this vehicle. The number of steps needed to do this job are too numerous to list in the space available. If your engine is the 2.4L four cylindar, it is the same procedure used to change the timing belt. If you are going into the water pump on this engine, you may as well change the belt and tensioner pulley. If you do not have a well equipped garage, I would not attempt this job.

Posted on Jun 05, 2011

  • 3 Answers

SOURCE: change a water pump on a dodge neon

If I'm not mistaking you need to get to the timing belt and remove it cuz the water pump goes in the timing belt.

Posted on May 09, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Firing order & Wire Routing for 2009 Dodge Nitro 3.7 w/ three coil setup


The firing order for v6 is 165432
The driver side cylinder bank is numbered from front to rear-- 2-4-6
The passenger side cylinder bank is numbered from front to rear 1-3-5
The picture is for your coil pack, hopefully. So you can see how the coil towers are numbered.
My database for 09 showed coil on plug ignition. Is this the original engine?
I did see info for 07--3.7L that did appear to show a coil pack in tune-up manual.

coil pack-44ygowsvu5lf44rkpv3xxwg3-3-0.jpg

Apr 20, 2017 | Dodge Cars & Trucks

1 Answer

How to replace a bypass nipple on the water pump housing


How do I change the bypass hose? - DodgeTalk : Dodge Car Forums ...

www.dodgetalk.com > ... > 2G Dodge RAM - General Talk
Mar 9, 2008 - I usually change the bypass hose every time I have the pump off for this very reason. ... Edelbrock ProFlow,52mm TB,180* t-stat,e-fans, pacesetter long tubeheaders, ..... Dodge B-Series Vans 1971 - 2003, Dodge Caravan/Grand Caravan ....DuoWing, Dodge Caravan General Talk, 1, 04-14-2007 09:46 PM ...

Aug 26, 2015 | 2000 Dodge Grand Caravan

1 Answer

09 buick enclave 2 cylinder misfire and lossing coolant


Is the head gasket leaking coolant into that cylinder ?
What does the spark plug look like, and how's the compression ?

Feb 05, 2014 | 2009 Buick Enclave

1 Answer

I need to replace water pump on a 2006 dodge ram


318 or 360 engine?
well, the removal procedure is about the same on both, remove fan and belts first, then remove the water pump, be careful not to damage the radiator, clean the block surface for the new gasket to sit uniformly again, and bolt new pump back on, tighten bolts 3/4", bottom out bolts first on a symetrical cross pattern., I would recommend changing the thermostat too, always a must when new pump is installed...

Good luck

Aug 23, 2011 | Dodge Ram 1500 Cars & Trucks

1 Answer

How do i change the water pump on a 2000 dodge,grand caravan


Removing and changing the water pump on a 2000 Grand Caravan should only be done if your van has a 3.3 liter or 3.8 liter V6 engine. On any other engine types, including four-cylinder engines, you must remove the timing belt from the engine to access the water pump, which is a dangerous task that can mess up the engine if attempted by an amateur.
The procedure is as follows:------------- The water pump is responsible for sending the engine coolant to the engine.First of all remove the serpentine belt then remove the plastic cove on the passenger side behind the wheel. You will have to remove the pulley. Once the pulley is removed unbolt the water pump and remove it. Clean the surfaces and install new pump. Draining the coolant and replacing it is advisable.
Drain the engine coolant, twisting and removing the drain plug at the bottom of the radiator
-------------------Thats it.

Nov 18, 2010 | 2000 Dodge Caravan

2 Answers

Change a water pump on a dodge neon


i need a diagrm for the cooling system on a 1999 dodge neon

Nov 09, 2009 | 1996 Dodge Neon

1 Answer

I am changing the water pump on my 94 dodge spirit 2.5L 4cyl. am down to the pump, have removed top 3 bolts holding pump on, but it still wont come off. cannot see what to do next. any thoughts? thanks.


try these websites www.autozone.com and www.alldatadiy.com if all fails stop by your local library and get your hands on Haynes auto repair manual for your car wish you the best of luck Michigan Man.

Sep 10, 2009 | 1994 Dodge Spirit

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...