What does the fault code P1336 TEC not learned mean

P1336 Cadillac Crankshaft Position System Variation Not Learned

P1336 Ford P1336 Ford - Crankshaft Position Or Camshaft Position Sensor Input Signal Error Share
0 ' Add Comment Possible causes
- Faulty Crankshaft Position Sensor
- Faulty Camshaft Position Sensor
- Crankshaft Position Sensor harness is open or shorted
- Crankshaft Position Sensor circuit poor electrical connection
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
What does this mean? When is the code detected?
The Engine Control Module (ECM) has detected a synchronization or signal error from the cam or crank sensors
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of Power
- Engine Stall
- Engine difficult to start
P1336 Ford Description
The input signal to the powertrain control module (PCM) from the crankshaft position (CKP) sensor or the camshaft position (CMP) sensor is erratic.

Read more: http://www.engine-codes.com/p1336_ford.html#ixzz3qT9Hiztc

The P0172 means "System too Rich Bank 2 and the P1336 means "Crank/Cam Sensor B Circuit Malfunction"

Trouble Code: P1336

CKP Sensor System Variation Not Learned
Possible Causes:


Set the parking brake and block the drive wheels for safety. Verify the hood is closed. Read the trouble codes. If a code is set, refer to that code. Start the engine. Allow engine temperature to reach at least 158?F (70?C). Then key off. Select Crankshaft Position Variation Learn procedure on Scan Tool & start the vehicle. Apply the brake pedal firmly and verify the selector is in Park. Increase accelerator pedal position until fuel cutoff is reached at the test rpm (e.g., 5150). Quickly release the accelerator pedal after fuel cutoff is reached. The CKP system variation compensating values are learned when the engine speed (rpm) decreases back to idle speed and the procedure terminates. Read the trouble codes and recheck for DTC P1336. If DTC P1336 runs and passes, the CKP system variation "learn" procedure is complete. If not, look for other codes. If no codes are set, repeat the test procedure.

This is from updated GM service manual of mine.

According to the GM factory service manual, the OBD-II trouble code, P1336, is defined as follows: DTC P1336 CKP System Variation Not Learned. The factory service manual does not enumerate all of the symptoms of this trouble code, but after consulting a professional custom PCM tuner, it was learned that aside from the annoying light on the instrument cluster, the other symptoms exhibited may include: poor vehicle performance, and loss of misfire detection diagnostics.

This DTC is particularly nasty, because simply clearing it by disconnecting the battery, or clearing it using an OBD-II scan tool will not address the problem. The code will be set again later unless the vehicle is run through the actual "crank relearn" procedure.

Fixing the Dreaded P1336 DTC

There is only one way to properly fix the P1336 DTC, and that's to perform a "crank relearn" procedure, or as the GM factory service manual procedure calls it, the CKP System Variation Learn Procedure. This procedure can be initiated and performed by GM's be-all end-all scan tool, the Tech-2. It can also be performed by some aftermarket scan tools. Furthermore, some of the PCM tuning software applications are capable of initiating a "crank relearn" procedure.

P1336 CKP System Variation Not Learned
please dont ask me what this means as i havent a clue

P0350 is Ignition coil primary/secondary circuit malfunction,could be faulty igntion coil or module.P1336 is crankshaft position system variation not learned.This is done with a Tech2 at your local dealership you would be best served taking this car to your dealer to have it diagnoised.

According to the GM factory service manual, the OBD-II trouble code, P1336, is defined as follows: DTC P1336 CKP System Variation Not Learned. The factory service manual does not enumerate all of the symptoms of this trouble code, but after consulting a professional custom PCM tuner, it was learned that aside from the annoying light on the instrument cluster, the other symptoms exhibited may include: poor vehicle performance, and loss of misfire detection diagnostics.

This DTC is particularly nasty, because simply clearing it by disconnecting the battery, or clearing it using an OBD-II scan tool will not address the problem. The code will be set again later unless the vehicle is run through the actual “crank relearn” procedure.

There is only one way to properly fix the P1336 DTC, and that’s to perform a “crank relearn” procedure, or as the GM factory service manual procedure calls it, the CKP System Variation Learn Procedure. This procedure can be initiated and performed by GM’s be-all end-all scan tool, the Tech-2. It can also be performed by some aftermarket scan tools. Furthermore, some of the PCM tuning software applications are capable of initiating a “crank relearn” procedure.

For most enthusiasts that encounter this issue, the best course of action is to bring the vehicle to a local GM dealership and have them perform the procedure. Unfortunately most dealerships will charge a modest fee for doing this (upwards of USD $100 in some cases).

I would think it would be just the Camshaft Position Sensor.I looked up the codes and they say pretty much the samething.


P0340 Ford Camshaft Position Sensor Circuit Malfunction


P1336 Ford Crankshaft/Camshaft Sensor Range/Performance

Change your crankshaft position sensor (CPS)

P1336 Crankshaft Position System Variation Not Learned