Do I need to use more force to pry the top of the cover off but the bottom of the cover came off very easily? Cant seem to find any you tube videos for this vehicle which makes it even trickier? TIA
2006 Honda StreamWorkshop Repair Service Manual PDF Download
for the easy solution download the pdf file
SOURCE: remove passenger tail light
I have not yet worked on a Pilot, but from experiance, a lot of tail lights are pulled from the inside and not the out. You may check to see if it comes out from the trunk and not straight off the back from the outside.
gabenevins, a lot of places are selling the entire assembly and not just the lens. I would continue looking until you find just the lens unless you want to buy the whole piece. I do not know what the cost difference is. Perhaps pjpc might be able to tell you where to get just the lens.
SOURCE: removing rear light assembly on honda odyssey 2006
Yes, there is a "spear point" plastic clip that is still engaged into a socket type holder in the front outboard portion of the tail lamp assembly. Pry gently with a tape wrapped screwdriver at the front outboard corner of the assembly and the clip will release. You will then be able to see how the clip works and will be able to align and engage it first when replacing the tail lamp assembly.
-T
SOURCE: 2005 Honda Odyssey brake light housing removal
Yes, there is a spear point style clip that is holding the assembly. Wrap a flat blade screwdriver with some masking tape (prevents paint scratches) and pry between the forward outboard corner of the brake light housing and the car body. You want to pry the assembly rearward.
SOURCE: 2006 Honda Accord Rotor removal.
I've been working on Honda's like this for years, including my own, and there are two ways that you can get the screw out. The easiest/best way to do it is with an impact driver and the biggest phillips screwdriver bit you can find (sorry can't remember the number, I think #4 but not sure). Once you have the bit you are good to go and your impact wrench will do the work for you. If you don't have an impact wrench the other way I've learned to do it is by taking a small (12" section) of rebar and a mini sledge hammer and put the rebar directly on the screw (make sure it is straight) and hit it with the hammer. Make sure you hit the rebar and not the car or yourself. You are probably going to have to hit this really hard to break it loose (you can try penetrating oil, not WD-40, along with this method). After you beat the screws for a while, you are going to need the biggest phillps screwdrive you can find, again not sure what size, and you will be able to get this out. If you have started to strip the screws you need to be very careful and if you aren't sure you can get them out without stripping them I might take it to a mechanic and have them loosen them up for you. Let me know if you have any further questions. Thanks for using FixYa!
SOURCE: cant remove the tail light assemblies on '09 accord sedan
youll have to pull up very firmly or it may have to slide to the side its held in place by a bodyfastener. a screw that fits into a slot. but i would try pulling up first.
Rear iignts in rear na, removing and instaiiing
Fig. 325: Rear Lights In Rear Lid, Removing And Installing
Courtesy of VOLKSWAGEN UNITED STATES, INC.
Removing
CAUTiON: • Switch off all electrical components.
. . Switch ignition off and remove ignition key.
o Turn light switch into "0" position.
o Open cap - 1 - for warning triangle.
o Rotate quick-release screw - 2 - counter-clockwise 90 C
and remove cover - 3 - from luggage compartment lining - direction of arrow -
Fig. 326: Removing Bulb Socket From Housing, Pressing Catch
Bracket Downward
Courtesy of VOLKSWAGEN UNITED STATES, INC.
o Disconnect electrical harness connector
o Remove bulb socket - 1 - from housing, press catch bracket
- 2 - downward - arrow - to do so
Fig. 327: Identifying Nuts, Clamping Bracket, Inner Tail
Lamp, And Clamp Mounting
Courtesy of VOLKSWAGEN UNITED STATES, INC.
o Unscrew nut - 2 - and remove clamping bracket - 1 -
o Remove nut - 4 - and remove inner tail lamp - 3 - toward
outside
o Remove clamp mounting - 5 - from body cut-out
Fig. 328: Identifying Clamp Mounting, Nuts, Inner Tail Lamp,
And Tabs
Courtesy of VOLKSWAGEN UNITED STATES, INC.
Installing
Installation is the reverse of removal, noting the
following:
NOTE: • Make sure seal between body and tail lamp housing
seals properly.
. Attach clamp mounting -2 - at inner tail lamp and screw on
nut -3 - loosely.
. Attach inner tail lamp -4 - at body cut-out and make sure
grip tabs - arrows - of clamp mounting rest against body cut-out
. Slide clamp mounting - 1 - onto threaded pin of inner tail lamp and tighten nuts - 3 - and -5 -.
347 views
Usually answered in minutes!
×