At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
On the Steering wheel are your control buttons for your digital display for controlling the sounds for your alarm, your sound for locking and unlocking. Also your trip meter, mpg display, and several other controls. You can set it up to give a signal noise or be silent.On the Steering wheel are your control buttons for your digital display for controlling the sounds for your alarm, your sound for locking and unlocking. Also your trip meter, mpg display, and several other controls. You can set it up to give a signal noise or be silent.
You can't post conmments that contain an email address.
1 hour ago - Question about 2002 Oldsmobile Bravada. Open Question ... The chime sound that should signal that I am unlocking my 2002 Oldsmobile Bravada, andshould also signal when I lock it is not working. Posted by francisco_al on Feb ... T & C 2001 REMOTE CONTROL PROGRAMMING. Sep 17, 2012 ' 2001 ...
1995 oldsmobile achieva dash and tail lights don't work! ... My car, 98 intrigue, has the automatic climate control and will not change ... Usually the whining noise stops just before it stalls. ... I have a 2002 Olds Bravada I bought during cold weather. ... both the cam and crank sensor send their signals to the ignition control ...
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Procedure #1 (Remote Head Keys WITH Immobilizer Chip)
Step-by-Step How To Programming Instructions:
CUT the NEW remote head key for your vehicle.
INSERT the first working remote head key into the Ignition.
TURN the Ignition to the ON position for at least three (3) seconds but no longer than fifteen (15) seconds.
TURN the Ignition to the OFF position and remove the first remote head key.
INSERT the second working remote head key into the Ignition.
TURN the Ignition to the ON position for at least three (3) seconds but no longer than fifteen (15) seconds.
After ten (10) seconds a chime will sound and the vehicle's security light will begin to flash.
TURN the Ignition to the LOCK position and REMOVE the second remote head key.
INSERT the NEW remote head key into the Ignition.
TURN the Ignition to the ON position within 60 seconds.
After ten (10) seconds a single chime will sound and the vehicle's security light will stop flashing.
The vehicle's security light will turn ON again for three (3) seconds and OFF to indicate successful programming.
Test all remotes. Programming is now complete. The remote and key are now both programmed.
If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.
Procedure #2 (Remote Head Keys WITHOUT Immobilizer Chip)
Step-by-Step How To Programming Instructions:
ENTER the Vehicle and CLOSE all doors.
INSERT key into Ignition.
TURN the Ignition to the ON position (before cranking).
PRESS and HOLD UNLOCK on a working remote head key for four (4) to ten (10) seconds.
WHILE holding the UNLOCK button, PRESS the PANIC button UNTIL a chime sounds to indicate entry into Programming Mode.
RELEASE both the PANIC and UNLOCK buttons.
PRESS the LOCK and UNLOCK buttons simultaneously on the same remote until a chime is heard.
Once the chime is heard, PRESS and RELEASE the UNLOCK button on that same remote. Another chime will sound indicating successful programming of that remote. (This MUST be done within 30 seconds)
WITHIN 30 seconds of Step 8, PRESS the LOCK and UNLOCK buttons on any other remotes to be programmed. RELEASE the buttons when the chime is heard. Again, PRESS and RELEASE the UNLOCK button on that remote. Another chime will sound indicating successful programming of that remote.
REPEAT Step 9 for ALL remotes (even working remote head keys) that you want to work with your Vehicle.
Test all remotes. Programming is now complete. The remote and key are now both programmed.
If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.
ATTENTION:You MUST HAVE one working remote to add one more to the system. 1. Press LOCK button 5 times at 2 second intervals to resynchronize remote. 2. Insert key into the ignition switch. Turn ignition to the RUN position (as far as you can go without cranking engine). Wait for ignition chimes to stop.
3. Using the working remote, press and hold the UNLOCK button on the remote for 4 to 10 seconds. 4. Within the specified 4 to 10 seconds, continue pressing the UNLOCK button and then press the PANIC button ( on the programmed remote ) for 1 second and release both buttons. A chime will sound to indicate that the remote programming mode has been entered ( allow 3 seconds for chime to sound ). 5. Within 30 seconds of the chime, press and release the LOCK and UNLOCK buttons simultaneously then press and release just the UNLOCK button on the same remote. A chime will sound indicating the remote has been programmed. Press and release the LOCK and UNLOCK buttons simultaneously and then press the UNLOCK button on each new remote you wish to program at this time. A chime will sound afer each additional remote is programmed. 6. Turn the ignition OFF and remove key. 7. Test Remotes.
You must have a programmed FOB to program another at home with my instructions below. If you don't have programmed one then you must get the first one programmed at the dealer.
Press LOCK button 5 times at 2 second intervals to re-synchronize remote.
Insert key into the ignition switch.
Turn ignition to the run (no start.)
Wait for ignition chimes to stop.
Using the working remote, press and hold the UNLOCK button on the remote for 4 to 10
seconds.
Within the specified 4 to 10 seconds, continue to hold the UNLOCK button and then press the PANIC button ( on the programmed remote ) for 1 second and release both buttons. A chime will sound to indicate that the remote programming mode has been entered ( allow 3 seconds for chime to sound ).
Within 30 seconds of the chime, press and release the LOCK and UNLOCK buttons simultaneously then press and release just the UNLOCK button on the same remote.
A chime will sound indicating the remote has been programmed. Press and release the LOCK and UNLOCK buttons simultaneously and then press the UNLOCK button on each new remote you wish to program at this time. Locks will cycle after each additional remote is programmed.
Directly from the owners manual... 1.- Enter your car wth your ignition key and your theft remote, and press the Lock button on your remote five times in 10 seconds. 2.- Insert your key into the Jeep's ignition cylinder, and then turn the key to the "Run" position. Wait for the car's automatic chiming sound to stop before proceeding. 3.- Press and hold the Unlock button on your remote for around five seconds, and then press and hold the Panic button at the same time. 4.- Hold both buttons together for one second and then release. Wait for the car's chimes to sound again and then press and release the Lock and Unlock buttons on your remote. 5.- Press and release just the Unlock button on the remote next and wait for a chime again to indicate successful programming. You can then remove your ignition key to complete the resetting process.
You must have one working
remote to add one more to the system. If you do not have one working remote
right now then these instructions will not work. You will have to have a
Locksmith or dealership use a computer to program the first remote for
you.
1. Press LOCK button 5
times at 2 second intervals to resynchronize remote. 2. Insert key into the ignition switch. Turn ignition
to the RUN position (as far as you can go without cranking
engine). Wait for ignition chimes to stop.
3. Using the working remote, press and hold the UNLOCK button on the
remote for 4 to 10 seconds. 4. Within the specified 4 to 10 seconds, continue
pressing the UNLOCK button and then press the PANIC button ( on the programmed remote ) for 1 second and
release both buttons. A chime will sound to indicate that the remote
programming mode has been entered ( allow 3 seconds for chime to sound
). 5. Within 30 seconds of the chime, press and release the
LOCK and UNLOCK buttons simultaneously then press and release just the
UNLOCK button on the same remote. A chime will sound indicating the
remote has been programmed. Press and release the LOCK and UNLOCK buttons
simultaneously and then press the UNLOCK button on each new remote you
wish to program at this time. Locks will cycle after
each additional remote is programmed. 6. Turn the ignition OFF and remove
key. 7. Test Remotes.
You must have one working
remote to add one more to the system. If you do not have one working remote
right now then these instructions will not work. You will have to have a
Locksmith or dealership use a computer to program the first remote for
you.
1. Press LOCK button 5
times at 2 second intervals to resynchronize remote. 2. Insert key into the ignition switch. Turn ignition
to the RUN position (as far as you can go without cranking
engine). Wait for ignition chimes to stop.
3. Using the working remote, press and hold the UNLOCK button on the
remote for 4 to 10 seconds. 4. Within the specified 4 to 10 seconds, continue
pressing the UNLOCK button and then press the PANIC button ( on the programmed remote ) for 1 second and
release both buttons. A chime will sound to indicate that the remote
programming mode has been entered ( allow 3 seconds for chime to sound
). 5. Within 30 seconds of the chime, press and release the
LOCK and UNLOCK buttons simultaneously then press and release just the
UNLOCK button on the same remote. A chime will sound indicating the
remote has been programmed. Press and release the LOCK and UNLOCK buttons
simultaneously and then press the UNLOCK button on each new remote you
wish to program at this time. Locks will cycle after
each additional remote is programmed. 6. Turn the ignition OFF and remove
key. 7. Test Remotes.
ATTENTION:You MUST HAVE one working remote to add one more to the system. If you do not have one working remote right now then these instructions will not work. You will have to have a Locksmith or dealership use a computer to program the first remote for you. Click here to find an Automotive Locksmith in your area to program this remote.
1. Press LOCK button 5 times at 2 second intervals to resynchronize remote. 2. Insert key into the ignition switch. Turn ignition to the RUN position (as far as you can go without cranking engine). Wait for ignition chimes to stop.
3. Using the working remote, press and hold the UNLOCK button on the remote for 4 to 10 seconds. 4. Within the specified 4 to 10 seconds, continue pressing the UNLOCK button and then press the PANIC button ( on the programmed remote ) for 1 second and release both buttons. A chime will sound to indicate that the remote programming mode has been entered ( allow 3 seconds for chime to sound ). 5. Within 30 seconds of the chime, press and release the LOCK and UNLOCK buttons simultaneously then press and release just the UNLOCK button on the same remote. A chime will sound indicating the remote has been programmed. Press and release the LOCK and UNLOCK buttons simultaneously and then press the UNLOCK button on each new remote you wish to program at this time. A chime will sound afer each additional remote is programmed. 6. Turn the ignition OFF and remove key. 7. Test Remotes.
1. Press LOCK button 5
times at 2 second intervals to resynchronize remote. 2. Insert key into the ignition switch. Turn ignition
to the RUN position (as far as you can go without cranking
engine). Wait for ignition chimes to stop.
3. Using the working remote, press and hold the UNLOCK button on the
remote for 4 to 10 seconds. 4. Within the specified 4 to 10 seconds, continue
pressing the UNLOCK button and then press the PANIC button ( on the programmed remote ) for 1 second and
release both buttons. A chime will sound to indicate that the remote
programming mode has been entered ( allow 3 seconds for chime to sound
). 5. Within 30 seconds of the chime, press and release the
LOCK and UNLOCK buttons simultaneously then press and release just the
UNLOCK button on the same remote. A chime will sound indicating the
remote has been programmed. Press and release the LOCK and UNLOCK buttons
simultaneously and then press the UNLOCK button on each new remote you
wish to program at this time. Locks will cycle after
each additional remote is programmed. 6. Turn the ignition OFF and remove
key. 7. Test Remotes.
Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question
ATTENTION:You MUST HAVE one working remote to add one more to the system. If you do not have one working remote right now then these instructions will not work. You will have to have a Locksmith or dealership use a computer to program the first remote for you.
1. Press LOCK button 5 times at 2 second intervals to resynchronize remote. 2. Insert key into the ignition switch. Turn ignition to the RUN position (as far as you can go without cranking engine). Wait for ignition chimes to stop.
3. Using the working remote, press and hold the UNLOCK button on the remote for 4 to 10 seconds. 4. Within the specified 4 to 10 seconds, continue pressing the UNLOCK button and then press the PANIC button ( on the programmed remote ) for 1 second and release both buttons. A chime will sound to indicate that the remote programming mode has been entered ( allow 3 seconds for chime to sound ). 5. Within 30 seconds of the chime, press and release the LOCK and UNLOCK buttons simultaneously then press and release just the UNLOCK button on the same remote. A chime will sound indicating the remote has been programmed. Press and release the LOCK and UNLOCK buttons simultaneously and then press the UNLOCK button on each new remote you wish to program at this time. Locks will cylce afer each additional remote is programmed. 6. Turn the ignition OFF and remove key. 7. Test Remotes.
Thanks for using FixYa - a Very Helpful rating is appreciated for answering your FREE question.
System warning lamp located on top of the instrument panel Press UNLOCK button once , turns on interior lamps and deactivates alarm (if fitted) Press UNLOCK button twice w/in 5 seconds unlocks all doors, turns on interior lamp and deactivates alarm (if fitted) To activate alarm system (if fitted): Switch ignition OFF Open driver's door Press Lock button on remote Close Driver door warning lamp will flash when system is activated Press remote power sliding door button will open sliding door (if fitted) only if unlocked first Pressing remote panic button: *Sounds horn intermittently *Flashes exterior lamps *Turns on interior lamps **Pressing panic for the second time OR switching ignition ON deactivates alarm.
PROGRAMMING
Remobe key from ignition switch Remove the "BCM PRGRM" fuse, from the fuse box Close all doors Turn ignition switch to the ACC position With in 1 SECOND , turn the ignition switch to OFF then back to 'ACC' (really, with in one second)
Open and close the driver's door. A chime will sound, indicating programming mode activated Press and HOLD LOCK and UNLOCK SIMULTANEOUSLY untill a chime sounds 2 times ( about 15 seconds) Repeat this exact procedure for all remotes to be programmed Remove key from ignition Refit 'BCM PRGRM' fuse.
On the Steering wheel are your control buttons for your digital display for controlling the sounds for your alarm, your sound for locking and unlocking. Also your trip meter, mpg display, and several other controls. You can set it up to give a signal noise or be silent.
×