How to change lightbulb can't get headlight off, have taken out 3 screws and pin

Vehicle's that are fitted with two terminal bulb's use two bulbs for dimm and bright.On the vehicle's that use three terminal's one bulb does the work of both. So i dont think it wiil work putting in that type of bulb unless you modify the headlight unit so it can accomidate two headlight bulbs per side.

Take out 1bolt just above headlight that holds headlight in place.Then to the left of headlight there is a 6inch pin you have to turn clockwise 1/4 turn then pull up and out.Remove headlight,ther is enough wire to put it to the side while you change the left turn signal.When the headlight is out of the way you can see the wires for the turn signal,turn the plug counter clockwise and pull,you will see lightbulb,pull out and change.To install do the reverse in order.

To replace the headlight bulbs.You need to remove the head light assembly out.The head light assembly is held by 2 to 3 three screws on each side. You need to remove those screws first.The front trim will get loose,the front trim is held by pins.The pins are of plastic and easy to release.Just release this pins and the front trim will get completely loose and can be easily taken off/. The head light assembly is in the front fender.Once the front trim is removed the head light assembly can be easily removed from front fender compartment.If its bit tight there,then you can use a screwdriver to give it a pull towards out.The head light bulbs can now be easily seen as well as easily removed now.Turn the bulb socket counterclockwise to remove the bulb from the bulb assembly. -------- Keep updated for any more queries.Thanks.

Access to change the headlamp bulbs is through the wheel well. The recommended method is to remove the front tire and then the plastic inner fender liner. Once removed, you'll have easy (more or less) access to the rear of the headlamp housing.

To change the low beam headlight on the 2001 Lesabre, the headlight assembly must first be removed from the car. It is really quite simple to do. There are two bolts on the top of the assembly that must be removed - that is all! The entire assembly comes out and gives easy access to the low beam bulb. Give it a 1/4 counterclockwise turn to remove it. Plus in the new one (#9006) and reverse the procedure.

how to change driver side headlight bulbs?

I've done this once, so i'll do my best to help you here. You'll need some sort of light you can shine to do this. First you need to unplug the headlight plug from the assembly. Next there will be a rubbery boot you also need to take off, this just pulls right off. This next part is where it gets sticky. There is a phillips screw that holds down a flexible pin/clamp/whatever you want to call it down against the back of the bulb. Unscrew the screw enough to remove the pin, you won't need to completely remove the screw though to remove the pin. Once you have the pin removed, you can then get at the bulb. The bulb itself has 3 points, like a down-ward arrow. Line up the 2 points that are closer together with the top and just slide the bulb in WITHOUT TOUCHING THE GLASS of the bulb. If you touch the glass, say goodbye to the bulb's life. To put it back together, get the bulb in, the pin screwed down and reverse the rest of the process. Hope this helps.

You have to remove the one screw that is holding it down , located on top of light assembly, ( for my 1998 it has only one screw!) then proceed to pull the assembly from the bottom pulling up , then just turn the round knob on the back of the assembly and remove defective bulb and replace with the new one . good luck !

hi may i suggest you locate the h/lights relay and check the pins for rust/mildew clean pins and refit and recheck lights? the relay to that bulb dip beam may be at fault? check h/book for location ? hope this helps ? as you seem to eliminated other possibilities

There are 2 screws one the frame above the headlight after you open the engine hood. One screw has a long shaft, both need to be removed and will release the headlight housing. Next you need to pull the headlight assembly out which might mean you have to push down on the plastic surrounding the assembly. Once the assembly is out all you need to do is pull up on the clip that holds the wiring and pull it off. There is a plastic ring around the lightbulb that you need to screw off and then you'll be able to pull out the bulb. Make sure you have a new HB5/9007 type replacement bulb, and do not touch the glass on the bulb with your fingers, if you do take a soft cloth and wipe the glass to remove any oils. After you place the new bulb in the assembly, put everything back in reverse of how you removed it and you'll be finished.