Question about 1994 Nissan Quest

Open Question

Torque on intake manifold bolts nissan quest - 1994 Nissan Quest

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 6982 Answers

SOURCE: Need torque specs for oil pan gasket

There likely is a spec for oil pan but unless you are a finatic, you really don't need to know what it is. Simple rule: Don't crank down ******* any fastener. If corners near crank ends have larger fasteners, you can tighten them a bit more than on siderails. Before tightening anything, install all bolts finger tight, to ensure that they are not cross threaded. To avoid warping pan, tighten from the center of the pan, working towards both ends, alternating from side to side as you go. When you are finished, go over it again, using the same amount of force on each bolt. As I said, end bolts can if larger in diameter, be tightened more but be careful not to tighten so much that you will either split or push the gasket out the sides.. Anywhere two gasket ends **** together, I recommend using a sensor -safe dab of silicone. An oil pan is not under any mechanical stress or pressure. I have used this method for many years and NEVER had one leak. If you really need #s, small fasteners get about 12-15in lbs, larger ones about 20.

Posted on Dec 31, 2008

Ad

SOURCE: head bolt torque settings for 720 nissan cab 2

dear friend-your torque setting on the 720 is the same as the L18 and is set at 85 - 90 nm.

Posted on Jul 23, 2009

  • 285 Answers

SOURCE: i just need the torque specs for the lower and

i solved it by finding someone that gave it to me for free

Posted on Sep 06, 2009

emissionwiz
  • 76846 Answers

SOURCE: how to remove front rotors on 2005 nissan quest

you need to remove the caliper mounting bracket assembly and then the rotors just slide off, go to link for pictures.
http://www.2carpros.com/how_to/how_to_replace_brakes.htm

Posted on Oct 02, 2009

saailer
  • 1868 Answers

SOURCE: Need torque specs for 2003 Nissan Murano AWD flex

Hello! Guru....Saailer

INTAKE MANIFOLD (sequence below)

STEP1........66"l bs. STEP2........21' lbs.

FLEX PLATE BOLTS

61" lbs.

FLEX PLATE to CONVERTOR

30' lbs.

Locktite on all the bolts.





10_23_2011_9_33_35_pm.gif

Posted on Oct 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

(1) What is the specific Newtom torque or lb-ft for the sparks plugs NGK LZKAR6AP-11 for Nissan Tiida St C-11 2011. Engine: MR18075675R, Vin:MNBBAC11A0016494.


You miss understand why things need to be torqued .
Torque is not specific to the vehicle its the bolt how hard what is thread pitch how many threads per in or mm how many bolts and what kind compression is required .
Compression always needs to be even say you have a cork gasket on an oil pan with 25 bolts 10 ft lbs on each would give you 250 ft lbs of force but if not done in stages evenly you would be snapping bolts and bending the pan and would leak oil from the start .
Spark plugs have seals 5/8 25 lb ft is fine but its not something you are going to get a torque wrench on .

Jun 15, 2016 | Nissan Tiida Cars & Trucks

1 Answer

98 ford windstar intake manifold torque specs


Intake torque specs ' FordForumsOnline.com

www.fordforumsonline.com > Ford Tech Forums > Engine & Drivetrain

May 7, 2010 - 2 posts - ‎2 authors
ISO torque specs for the intake & plenum for a 98 Windstar...3.8 with the ... Our community is here to help you with any questions you have related to your Ford. ... Lower Intake Manifold to Cylinder Head Bolt 8-12 - (71-106).

Torque Specifications - AutoZone

www.autozone.com/.../Ford-Windstar.../Specifications/Torque-...

AutoZoneAutoZone Repair Guide for your 2004 Ford Truck Ranger 2WD 2.3L MFI DOHC 4cyl Engine Mechanical Specifications Torque Specifications. ... Ford Windstar 1999-2003 ... Bolts, Main Bearing Bolts, Rod Brearing Bolts, Crankshaft Damper Bolts, Flywheel Bolts, Manifold. Intake, Exhaust ... Vehicle: 2008 Ford F150, 98 Civic.

Dec 21, 2015 | 1998 Ford Windstar

1 Answer

I need torque specks for valve train for a 1987 nissan truk v6 3.0 litter


cylinder head bolts 40 - 47 ft lbs, intake manifold bolts 12 - 14 ft lbs. , intake manifold nuts 17 - 20 ft lbs. , rocker arm shaft bolts 13 - 16 ft lbs. exhust manifold bolts 13 - 16 ft lbs. i hope this helps.

Dec 22, 2010 | Nissan Pickup Cars & Trucks

2 Answers

What are the torque measurements for the rocker arms and intake manafold?


2.2L Engine & 2.4L Engines
These engines are not equipped with rocker arms. The camshafts directly actuate the valves.

3.1L Engine & 3.4L Engines
When install or connect the check the following:
- Pushrods and the rocker arms. Torque the bolts to 24 ft. lbs. (32 Nm). - Rocker arm cover using a new gasket. Torque the rocker cover bolts to 89 inch lbs. (10 Nm).
- Heater bypass pipe. Torque the screw at the water pump to 106 inch lbs. (12 Nm), the bolt at the cylinder head corner to 18 ft. lbs. (25 Nm) and the nut to 18 ft. lbs. (25 Nm).


About the INTAKE MANIFOLD...
-
Intake manifold nuts and bolts and tighten to 89 inch lbs. (10 Nm)
- Pushrods and rocker arms. Torque the bolts to 89 inch lbs. (10 Nm) plus an additional 30 degree turn. - Lower intake manifold. Apply sealant to the threads of the bolts and torque the bolts to 115 inch lbs. (13 Nm).



859cdc3.jpg

Exploded view of the upper and lower intake-3.1L & 3.4L engines


fe92b8b.jpg

Fig. Lower intake manifold tightening sequence-3.1L & 3.4L engines

Hope help.

May 04, 2010 | 2000 Pontiac Grand Am GT

1 Answer

Intake manifold bolts torque and rocker arm torque


Intake Manifold Coolant Pipe Bolt .... 89 in lbs (7.4166 ft. lbs)
Lower Intake Manifold Bolt .............. 115 in. lbs (9.5833 ft. lbs)
Upper Intake Manifold Bolt/Stud ...... 18 ft. lbs
Valve Rocker Arm Bolt ................... 168 in. lbs (14 ft. lbs +30 degress

Feb 06, 2010 | 1999 Buick Century

2 Answers

Torque and sequence to Intake Manifold for 3.3L Nissan Xterra 2000


Hi El Faraon,
I believe that you're dealing with 12 mm bolts and nuts....THESE ARE NOT THE SPECS FOR YOUR ENGINE, but I believe that if you use them you'll be close....Tighten in three stages up to 22nm....choose the bolts from the centre of the manifold and circle outwards until you reach the last one.....It may be a good idea to draw an overhead or plan view of the unit, marking out the bolt positions.....Start at the centre and mark the sequence and follow that....What is important is starting at the centre, so that nothing becomes warped....

Hope this helps,

Regards, Johngee10

Sep 06, 2008 | 2000 Nissan Xterra

Not finding what you are looking for?
1994 Nissan Quest Logo

Related Topics:

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...