What is the head bolt torque on a 1993 festiva 1.3 engine

Here are some general torque specifications for the 1997 Ford Festiva's engine and suspension components. However, please note that these specs can vary based on the specific model and engine type. It's always best to refer to your vehicle's repair manual for precise information:

**Engine Torque Specs (in foot-pounds):**
- Cylinder Head Bolts: 35-50 ft-lbs
- Exhaust Manifold Bolts: 13-16 ft-lbs
- Intake Manifold Bolts: 18-24 ft-lbs
- Main Bearing Cap Bolts: 51-61 ft-lbs
- Rod Bearing Cap Bolts: 23-27 ft-lbs
- Flywheel Bolts (Manual Transmission): 58-73 ft-lbs
- Flywheel Bolts (Automatic Transmission): 61-76 ft-lbs

**Suspension Torque Specs (in foot-pounds):**
- Ball Joint Nut: 30-40 ft-lbs
- Control Arm Bolts: 60-80 ft-lbs
- Shock Absorber Upper Mount Nuts: 14-21 ft-lbs
- Shock Absorber Lower Mount Bolt: 40-55 ft-lbs

Remember that these values are approximate and can vary based on the specific model and any modifications made to the vehicle. Always refer to your vehicle's repair manual or consult a professional mechanic for accurate torque specifications to ensure proper installation and safety.

https://www.autozone.com/repairinfo/specifications/specificationsMain.jsp?childCatName=Head+Bolt+Torque&childCatId=25100244&categoryNValue=25199999&categoryNameForTitle=Internal+Engine&categoryName=INTERNAL+ENGINE&childCategoryNameForTitle=Head+Bolt+Torque
You can check several web site for this info

Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

These are the torque valies and sequences for your engine
Torque in 2 steps [1st (33-41 ft-lbs),
2nd (63-73 ft-lbs)]


Torque sequence: (for each bank)
------------
6 4 2 8

5 1 3 7
------------
Good luck and please rate this solutuon

Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.

Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.

B2500 4 Cylinder

Torque sequence: --------- ' 10 6 2 4 8 ' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51 Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final tighten all bolts an additional 90 to 100 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.

B3000 3.0 6 Cylinder

Torque sequence ---------- ' 6 4 2 8 ' ' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque to 73 Ft/Lbs

B4000 4.0 6 Cylinder

Torque sequence --------- ' 5 1 3 7 ' ' ' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs Step 3: turn cylinder head bolts in sequence an additional 90-degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.

Good luck with this job!

1978 - 1980 FORD FESTIVA 1.6L 65-70 Foot pounds (Final torque)
Torque sequence 9 3 1 5 7 8 6 2 4 10 Step 1: torque to 5 Ft/Lbs Step 2: torque to 20-30 Ft/Lbs Step 3: torque to 50-55 Ft/Lbs Step 4: torque to 65-70 Ft/Lbs Recheck final torque in sequence


1988 - 1993 F0RD FESTIVA 1.3L Torque sequence front of engine 8 4 1 5 9 7 3 2 6 10 Step 1: torque to 35-40 Ft/Lbs Step 2: torque to 56-60 Ft/Lbs Recheck final torque in sequence

2011 FORD FESTIVA 1.6L NO TORQUE SPECS AVAILABLE THERE IS NO FORD FESTIVA MANUFACTURED IN 1998 ALSO NO FORD FESTIVA MANUFACTURED WITH A 1.5L ENGINE
HOPE THIS HELPS YOU

You may have to grab a sheet of paper and draw this out.
Standing in front of the engine, on the left side of the head, assign the bolts the following numbers from from to back: 8,4,1,5,9. On the passenger side, front to back, assign the bolts the numbers: 7,3,2,6,10.

Step 1: Tighten all bolts to 22 ft lbs.
Step 2: Tighten all bolts to 45 ft lbs.
Step 3: Tighten bolts #1,2,3,4,5,6 to 110 ft lbs.
Step 4: Tighten bolt #7 to 100 ft lbs
Step 5: Tighten bolts #8,9,10 to 110 ft lbs.

Be sure to follow that procedure so you don't warp your head or damage the head gasket.

step one is 22 ft lbs.
step two is 52 ft lbs
step #3 is turn an additional 90 degrees. sart in the middle and work your way out going top tobottom, good luck.

hello,230e with engine 102.982,cylinder head bolt,double hexagonal socket m12, stage 1, 55 newton meter,stage 2 90 degrees stage 3 90 degrees,4 pcs. bolt with m8 tighten to 25 nm.ref. technical data year 1993,ty

Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): Foot pounds (Final torque) Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. Foot pounds (Final torque) Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.