Freon capacity chart

SOURCE: 2003 Grande Caravan Trans fluid capacity

Have you checked the owners manual? Called the dealer or a local transmission shop? Also, does it have an external cooler? this will make a difference. Are you changing the fluid and filter and need to know how much to put in? If so start with 3 liters/quarts and then cycle through the gears from park to low allowing each gear to engage. keep checking the fluid level as you go, fluid is checked with the vehicle running and in park.

SOURCE: Need to replace the heater core in a 1995 Dodge Grand Caravan SE

1991-95 Models

1. Disable the air bag system by disconnecting the negative battery cable.
2. Have the system discharged by a qualified professional mechanic using an approved recovery/recycling machine.
3. Drain the cooling system.
4. Remove the steering column cover and left and right side under panel silencers.
5. Remove the center bezel by unclipping it from the instrument panel.
6. Remove the accessory switch carrier and the heater/air conditioning control head.
7. Remove storage bin and lower right instrument panel.
8. Disconnect the blower motor lead under the right side of the instrument panel.
9. Remove the right side 40-way connector wiring bracket.
10. Remove the lower right reinforcement, body computer bracket and mid-to-lower reinforcement as an assembly.
11. Disconnect the vacuum lines at the brake booster and water valve.
12. Clamp off the heater hoses near the heater core and remove the hoses from the core tubes. Plug the hose ends and the core tubes to prevent spillage of coolant.
13. If equipped with air conditioning, remove the H-valve and condensation tube.
14. Disconnect the temperature control cable and vacuum harness at the connection at the top of the unit.
15. Remove the retaining nuts from the package mounting studs at the firewall. Disconnect the hanger strap from the package and rotate it aside.

1. Remove the temperature control door from the unit and clean the unit out with solvent. Lubricate the lower pivot rod and its well and install. Wrap the heater core and/or evaporator with foam tape and place in position. Secure with the screws.
2. Assemble the unit, making sure all vacuum tubes are properly routed.
3. Install the assembly to the vehicle and connect the vacuum harness. Install the nuts to the firewall and install the condensation tube. Fold the carpeting back into position.
4. Connect the hanger strap from the package and rotate it aside. Install the 2 brackets supporting the lower edge of the heater housing. Connect the blower motor wiring, resistor wiring and the temperature control cable.
5. Install the retaining screws from the right side to the steering column. Install the instrument panel trim covering and reinforcement.
6. Assemble the unit, making sure all vacuum tubes are properly routed.
7. Install the assembly to the vehicle and connect the vacuum harness. Install the nuts to the firewall and install the condensation tube. Fold the carpeting back into position.
8. Connect the hanger strap from the package and rotate it aside. Connect the blower motor wiring and temperature control cable.
9. Install the lower right reinforcement, body computer bracket and mid-to-lower reinforcement as an assembly.
10. Install the right side 40-way connector wiring bracket.
11. Install the lower right instrument panel and storage bin.
12. Install the heater/air conditioning control head and accessory switch carrier.
13. Install the center bezel to the instrument panel.
14. Install the under panel silencers and steering column cover.
15. Install the vacuum lines at the brake booster and water valve.
16. Connect the heater hoses to the core tubes.
17. Using new gaskets, install the H-valve and connect the refrigerant lines. Install the condensation tube.
18. Have the system evacuated and recharged by a qualified professional mechanic, utilizing the proper equipment. Add 2 fl. oz. (59 ml) of refrigerant oil during the recharge. Fill the cooling system.
19. Perform the Air Bag System Check procedures outlined in this section before connecting the negative battery cable.
20. Connect the negative battery cable and check the entire climate control system for proper operation and leaks.

SOURCE: Dodge 2005 Grand Caravan water Pump replacement

JUST COMPLETED THIS JOB TODAY. MAKE SURE THE ENGINE HAS COOLED DOWN . IT TOOK APPROX 2 1/2 HRS. DISCONNECT THE NEGATIVE POST ON THE BATTERY. JACK UP PASSENGER SIDE FRONT AND SUPPORT ON JACK STANDS. REMOVE PASS. FROUNT TIRE. DRAIN RADIATOR INTO CONTAINER FOR PROPER DISPOSAL OR REUSE. USING FLOOR JACK PROVIDE SLIGHT TENSION ON OIL PAN WITH A SHORT 2 X 4 WOOD PIECE TO PROTECT OIL PAN. LOOSEN 3 ENGINE MOUNT BOLTS ON PASS. SIDE OF ENGINE COMPARTMENT. ALLOW APPROX 1" BETWEEN SHOULDER OF BOLTS AND MOUNT. LOWER ENGINE UNTILL BOLTS ARE SET ONTO MOUNT. REMOVE ENGINE SPLASH SHIELD INSIDE WHEEL WELL OF REMOVED TIRE. LOCATE WATER PUMP AND LOOSEN 3 PULLEY MOUNTING BOLTS (THIS IS WHILE BELT IS ON PULLEY) REMOVE SURPENTINE BELT AND CONTINUE TO FULLY REMOVE THE PUMP PULLEY. IT WONT COME OUT AS THE PUMP & PULLEY HAVE TO COME OUT TOGEATHER. REMOVE 5 WATER PUMP BOLTS AND CAREFULLY WORK WATER PUMP OUT BETWEEN THE ENGINE AND VEHICLE FRAME. CLEAN ALL MATING/GASKET SURFACES AND BOLTS. USING A SMALL AMOUNT OF TACKY SEALENT TO INSURE THE NEW WATER PUMP SEAL STAYS IN PLACE, THE INSTALL IS PRITTY MUCH THE REVERSAL OF REMOVAL.

GOOD LUCK, REMEMBER TO TIGHTEN ALL BOLTS TO MFR SPECS AND BLEED THE AIR OUT OF THE COOLANT AS REQUIRED.

SOURCE: 2005 dodge grand caravan heat not working. one

There is a recall that has something to do with the air/heat system in 2005 Dodge Grand caravans. Recall F01. Here is a link. I had mine done two weeks ago, cost me nothing. My air conditioner was overheating.

SOURCE: Size of rims on my 2005 Dodge Grand Caravan

Read the side of the tire. It will read like P225-70- 15 the last number is the diameter of the wheel. 14=14 inches 15=15 inches and so on.