Main fuserelay where is this located

The main fuse on the JCB 8014 mini digger is typically located near the battery or the starter motor. Here are some steps you can take to locate the main fuse:

1. Locate the battery: The main fuse is usually located near the battery or the starter motor. Locate the battery and follow the cables that are connected to it.
2. Follow the cables: Trace the cables that are connected to the battery and look for a fuse holder along the way. The fuse holder should be a small plastic box with a lid that can be opened.
3. Check the manual: If you have the owner's manual for the JCB 8014 mini digger, check the fuse diagrams to see where the main fuse is located.
4. Check the fuse box: The main fuse may be located in the fuse box under the hood or in the cab. Check the fuse box for a large fuse that is rated at 60 amps.
5. Consult a technician: If you are unable to locate the main fuse, it is best to consult a qualified technician who can help you locate and replace the fuse.

Once you have located the main fuse, check it for signs of damage or burn marks. If the fuse is blown, replace it with a new one of the same amperage rating. If the fuse is not the issue, there may be a problem with the wiring or the electrical components of the mini digger, which may require further diagnosis and repair by a qualified technician.

Check the brake switch at the top of the brake pedal arm.

Most main fuses are located close to the positive battery cable and in some cases attached directly to the positive cable located in a plastic box with a cover. There may also be a fusable link used for a main fuse which will connect to the starter

it is typically located in the main fuse box in the engine compartment. the exact location depends on the model of the car. once you locate it, open the cover and there will be a schematic showing the allocation of fuses

The main relay is usually located on the drivers side under the dash. It is usually brown, rectangle shape about half the size of a stick of butter, with about an 8 pin connector. Let me know if this helps.

it's called the tcm located in the main fuse panel under the hood in the main fuse box. you have several 'main' fuses located in the main fuse and relay box. look on the drivers side fender well under the hood. lift the black box lid off and it will reveal the main relays and fuses you seek. thank you for choosing fixya.com! i look forward to assisting you in the future!

When people use the term flash, they really mean the computer needs programmed

It's going to be your main relay, located under the dash on the drives side, turn key on and off, you will he a clicking sound, that the main relay control your power to you computer also.

The fuses are located in fascia fuse box,located under steering wheel,check owners manual for exact location
f10 is r/h main beam 10 amp
f11 is l/h main beam 10 amp
If fuses ok check bulbs

The main relay is located behind left side of the dash and above and behind the fusebox and above the hood release.

rate this solution fixya.

Diagram below:-

Acura Main Relay location and removal procedures.
Integra EFI Main Relay for:

• Honda Civic/CRX/del Sol 1984-1995
• 1986-89 INTEGRA
• 1990-93 INTEGRA #39400-SH3-003 RELAY (RZ-0063)
• 1986-90 LEGEND #39400-SH3-003 RELAY (RZ-0063) (RZ-0046)
• 1991-93 LEGEND (rz-0105)
• VIGOR (behind the left front kick panel)

The main relay is located behind left side of the dash and above and behind the fusebox and above the hood release. The First generation Legend main relay location is between the steering column and the fuse box. It's deep in there. There was a little difficulty drawing the relay so it's actually very deep in there. There is a device (a relay) blocking the main relay. You will need to remove it to get a view of the main relay. The removal procedure is the about the same as the Accord's procedure.


Legend, 96-98 Acura TL main relay Acura Integra 98-01 main relay location:

Locating the main relay using your ears and fingers:
Steps:

1. Turn the ignition to ON. You should hear two clicks (a thousand of a second apart) under the left or right side of the dash board. One click is for the ECU/Injectors the other is for the fuel pump. At this moment the check engine light should come on.
2. Listen carefully at the moment the clicks engage (usually somewhere underneath the dashboard.) Reach in and touch the main relay.
3. 2 seconds later you should feel a click if the main relay is at least working or wait until it works. At this moment the check engine light should go out.
4. Turn the ignition to start and you should feel a click, turn engine off you should feel another click.
5. Most main relays should have seven terminals. Please check if the location is already listed below.

How do I get the main relay out?
Steps: See four ways below so you can get it out. First you have to reach high up in there and do all this with one hand and a flashlight.
A. Unbolt the bolt using a 10mm socket (picture A) or
Ab. Unclip the clip from the steel tab and slide it apart (picture A) or
B. Separate the steel tab from the plastic case (picture B) with a large flat screw driver jam and twist between the plastic case and the tab or
C. Disconnect the negative battery terminal. Unclip two clips I pointed with two arrows (picture C, or below) with a small flat head screw driver or with a strong thumb and then yank it out (D.) This is the preferred choice by many. Mechanics prefer choice A and maybe B. See detailed relay circuit photo.