Cars & Trucks Logo
R
Richard von Ernst Posted on Dec 20, 2013
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

Re-attaching the pull ******** the drivers door

I need to remove the upper panel on the drivers door to re-screw and attach the pull strap. Not sure if it's only the visible two screws holding it on.

Answer This Question

1 Answer

windsorguzzi

Level 3:

An expert who has achieved level 3 by getting 1000 points
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.
Master:

An expert who has achieved Level 3.

  • Master 796 Answers
  • Posted on Dec 20, 2013
windsorguzzi
Master
Level 3:

An expert who has achieved level 3 by getting 1000 points
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.
Master:

An expert who has achieved Level 3.

Joined: Jan 13, 2009
Answers
796
Questions
1
Helped
189456
Points
2084

Normally there are also other screws hidden behind chrome trims that you prise off with a plastic screwdriver. There are always plastic poppers all round the edges of the panel, use 2 screwdrivers slid in (one on each side of each popper) to lever the panel away from the door so that the popper comes out of the door.

5 Related Answers

Anonymous

  • 1990 Answers
  • Posted on Feb 02, 2009

SOURCE: Help with drivers door panel removal 2003 Deville

Look really close for Screw Hole Covers. These are Small Plugs that they Install from Factory to Clean up the Visible Screw Holes. Please Rate My Response! Thanks!

Ad

Anonymous

  • 253 Answers
  • Posted on May 05, 2009

SOURCE: driver door panel removal and re-connect door pull

You most likley have a damaged inside door handle. To remove the door panel, you must first remove the handle bezel. The trim piece around the handle. It is held in place by 4 retainer tabs, take a small flat screw driver, insert it between the bezel and handle. Gently pry away from the handle. If you look in the crack around the handle you will see the tabs. When you get that off, remove the switch assembly by prying up on it gently, unplug the wiring. There are 2 screws in the door panel where you pull the door shut, remove those also. Start at the bottom front of the door panel, pull outward firmly, but not violent. The retainers will come out, you will most likley break some, this is common. The inside handle is about $45 from your dealer. If it is the handle it is held in with 1 rivit, drill it out with a 3/16 drill. Replace the handle, reassemble. Good Luck.

Anonymous

  • 12 Answers
  • Posted on May 23, 2009

SOURCE: How to remove drivers door panel from 1997 Cadillac Deville.

try to look at stress point on door by handle normally two screws and under neath panel to screws also disconnect side panel for side mirror door of using panel popper

Anonymous

  • 1 Answer
  • Posted on Sep 16, 2009

SOURCE: 1988 Cadillac Deville drivers window shattered while up

Take the Lights out of the arm rest and you will see more screws.

Anonymous

  • 10515 Answers
  • Posted on Sep 20, 2010

SOURCE: I am trying to remove

Hi,

Let me provide you with generic guide i have for these models.If that wouldn't help, i would search some more details till you resolve this problem.

Tools Required
J 36796 Clip Zip Clip Removal Tool
Removal Procedure

1. Lower the window.

moz-screenshot.pngmoz-screenshot-1.png353f9ef.jpg

2. Remove the door bezel trim cover.

bd88a7a.jpg

5. Use the J 36796 to release the retainers (1) from around the outside edges
of the door trim panel.
6. Slide the door trim panel upwards to release it from the door.
7. Disconnect the door handle cables.


Installation Procedure

92c8024.jpg

1. Slide the electrical connector (2) into position on the water deflector.
2. Connect the door handle cables.
3. Align the alignment datums (1) and the electrical connector with the door.

a409aec.jpg

4. Install the door trim panel by applying pressure around the door trim panel to
secure the retainers (1) to the door.

a4643ad.jpg
Notice: Refer to Fastener Notice in Cautions and Notices.
5. Install the door trim panel screws. Tighten the screws to 1 N.m (9 lb in).

64d6ef5.jpg

6. Fold the trim cover flap down.

Note - The above is a generic procedure.You might need to make some adjustments,if required.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Remove glove box volvo 850 1997
Open the glove box door. The 2 plastic limit straps that attach to the door have small tabs on the side. With a very small screw driver depress these and detach the straps. Remove the under dash panel. Remove all the screws holding the box in and pull the box out.
Read full answer
Dec 28, 2013 • 1997 Volvo 850
0answers

How to remove inside door panel
Read full answer
Be the first to answer Aug 29, 2012 • 2002 Chrysler Sebring
0helpful
1answer

The door handle on the driver's side is broken...if you try to pull the handle the door does not open, you need to open it from the inside to get it open. How do we fix it?
1. You need to remove the door panel on the inside of the door first.
2. Make sure the window is all the way up.
3. Remove approximately 2 or 3 screws and the rod that is attached to the handle from within the inside of the door.
4. Replace with new handle attach screws and attach rod.
5. Put door panel back on and your done.
Read full answer
Oct 11, 2010 • 1990 Oldsmobile Silhouette
1helpful
1answer

Trying to remove rear door handle on chrysler lhs 99
Hello, to remove and replace the rear door try the following:

1. Disconnect the negative battery cable from the battery of your Chrysler LHS. You can accomplish this with an open end wrench, to prevent any injury or short in the electrical system as you are working on the door lock switch. Place the negative battery cable out of the way so it does not touch any metal parts.


2. Undo any screws that are holding the lower door panel to the door with a screwdriver. Unclip the plastic hold clips that are attached to the back of the panel by carefully pulling them away by hand.

3. Locate the electrical connector wires. These wires run behind the panel to the door arm rest and detach each wire connector by hand. Remember how the wires were attached so you can put them back the same way when it is time to reattach them.

4. Lower the door panel away from the door. Then, remove any screws holding the upper door panel in place. Remove the door handle pull cup that covers the door lock switch and door handle by carefully popping the cover off after you have removed the screws holding it in place.

5. Detach the upper door panel from the door. You can do this by pulling it away carefully from the plastic clips. Move the upper door panel out of the way and locate the door lock actuator switch. Remove the screws from the actuator switch that are holding it in place and disconnect the electrical wires attached to the back of the switch.

6. Replace the old door lock actuator switch with a new one. This replacement can occur by connecting the electrical wires to the back of the new switch and reattaching the switch to the door frame with screws. Put the upper door panel back in place, securing it to the door frame with plastic clips and screws.

7. Reattach the door handle pull cup to the upper door panel with screws. Then, put the lower door panel in place and reattach the electrical wires to the window switches underneath the armrest. Attach the lower door panel to the door frame with plastic clips and screws.

8. Attach the negative battery cable to the Chrysler LHS battery with the open end wrench.

Thanks













































Read full answer
Jul 27, 2010 • 1999 Chrysler LHS
1helpful
1answer

How do i remove the driver's inside panel door? My electric button panel for windows and locks isn't moving.
Like reference guide, check this procedure to Removal & Installation / Door Lock Motor...

The door lock motor is integral with the door latch. If the door lock motor is found to be defective, the entire door latch must be replaced.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Roll the door glass down.
  3. Disengage the 2 clips attaching the speaker grille to the door trim panel. (They are at the front of the grille, one near the top, and the other one at the bottom).
  4. Remove the 3 large washer-headed screws surrounding the speaker.

    6acb803.jpg
    Fig. Fastener location for the door lower trim panel
  5. Remove the access cover at the front of the door trim panel. Remove by prying at its rear edge.
  6. Remove the red courtesy reflector from the lower tail of door. Disengage by prying at the screwdriver notch at the bottom of the reflector.
  7. Remove the flag trim panel from the door by prying it off at the 2 attachment clip points.
  8. Remove the 7 screws attaching the door trim panel to door:
    1. One screw is located at the lower rear screw pocket.
    2. Three screws are located along the bottom of the door.
    3. One screw is located inside the handle opening.
    4. One screw is located at the upper front.
    5. One screw is in the pull cup.
  9. Disengage the 2 hidden clips attaching the rear of the trim panel; pry them off at the 2 attachment clip points.
  10. Lift the trim panel upward and away from the door, disengage the trim panel from the upper retainer channel.
  11. Disengage the clip attaching the latch linkage to back door handle.
  12. Disconnect the electrical connectors as necessary, including the lower foot light, if equipped.
  13. Remove the door trim panel from the door.
  14. Remove the water shield (water dam) from the inside of the door.

    b5ff0ae.jpg
    Fig. Remove the flag trim panel, door trim access cover, inside remote handle, and power door lock switch
  15. Raise the door glass.
  16. Remove the bolt and nut for the rear glass run channel and position the channel aside.
  17. Disconnect the lock rod from the lock button bellcrank.
  18. Disengage the lock and latch rods from the clips on the inner door panel.
  19. Disconnect the lock and latch rods from the outside door handle and the key cylinder at the door latch.
  20. Disconnect the wire connector from the power door lock motor.
  21. Remove the screws attaching the door latch to the door end frame.
  22. Remove the door latch and the power door lock motor from the vehicle.

    c5c04cf.jpg
    Fig. Expanded view of the door lock, latch, and linkage


    185c44d.jpg
    Fig. View of the door lock button, latch rod, lock rod, and door latch

Hope helps (remember rated this).
Read full answer
Jun 26, 2010 • 2000 Chrysler Sebring
2helpful
1answer

I have a 1999 chevy blazer I cannot close the
The sunroof is powered by the same circuit breaker that power's your power window, so if your windows work than the circuit breaker should be good. You needed test the switch to verify if works with; on the factory sunroof system the roof is controled by a sunroof module the module receives a signal from the switch then throws voltage to the sunroof motor. The motor and module are located between the sunroof assembly and windshield underneath the head liner. You would reconnected the switch and test to see if the sunroof motor is getting power when the switch is in use by testing the dark green wire when closing and a light green wire when opening. Test these wires at the sunroof motor with a ohm meter or test light. Also, check this procedure to repair...

GM S-Series Pick-ups and SUV's 1994-1999 Repair Guide Power Sunroof - REMOVAL & INSTALLATION

Glass
  1. Close the sunroof and open the sunshade.
  2. If the piece of glass being removed is to be reinstalled, mark the location of the screws, this will ensure proper alignment during installation.
  3. Unfassten the screw that attach the sunroof glass to the sunroof assembly.
  4. Remove the glass from the vehicle.
To install:
  1. Place the glass into position and install the screws that retain the glass. Do not fully tighten the screws just yet.
  2. Adjust the glass so that the fit between the glass and the opening is equal at all four sides. The rear edge of the glass may be slightly higher than the front edge to reduce the wind noise.
  3. After the glass has been adjusted, tighten the screws to 31 inch lbs. (3.5 Nm).
  4. Check the operation and fit of the glass.

Motor
  1. Disconnect the negative battery cable.
  2. Remove the sunroof opening trim by starting at the **** joint and pulling the trim strip from the sunroof opening.
  3. Remove the headlines as follows:
    1. If equipped, remove the overhead or sunroof console.
    2. If equipped, remove the dome lamp.
    3. Remove the coat hooks and the assist handles.
    4. Remove the sunshade-to-roof screws, while pulling down on the sunshade base, push in on the extended screws, loosen the screw that attaches sunshade to the roof and pull down on the sunshade retainer while pushing in on the extended screw. Remove the retainer.
    5. Remove the windshield garnish moldings using trim removal tool J 38778 or its equivalent. Pull the molding away from the pillar and up to remove it.
    6. On four door models, remove the body lock pillar trim panels.
    7. Remove the roof rear header garnish molding using the trim removal tool. Insert the tool into the front edge of the trim and work along the front of the panel, from one end to the other. Unplug the cargo lamp electrical connection and remove the trim.
    8. On two door models, remove the rear seat upper seat belt anchor bolts.
    9. Remove the upper and lower front seat belt anchor bolts.
    10. Remove the rear seat belt lower anchor nut (two door models only).
    11. Remove the end gate or liftgate opening sill plate.
    12. Remove the jack storage cover (left side).
    13. Remove the upper body side trim panel screw (left side).
    14. Remove the upper body side trim panel and the body side front lower trim panel.
    15. Remove the headliner from the vehicle.
  4. Remove the sunroof console mounting bracket.
  5. Remove the straps that retain the wiring harness.
  6. Tag and unplug any necessary electrical connections.
  7. Unfasten the screws that attach the motor to the sunroof assembly.
  8. Remove the motor from the vehicle. Make sure that you do not move the sunroof mechanism while the motor is not in place.
To install:
  1. Place the motor into position and install the retaining screws. Tighten the screws to 31 inch lbs. (3.5 Nm).
  2. Attach all electrical connections that were unplugged.
  3. Attach the straps that retain the wiring harness.
  4. Install the sunroof console mounting bracket.
New headliners must be pierced to accommodate actual vehicle accessories.
  1. Install the headliner as follows:
    1. Install the body side front lower trim panel and the upper body side trim panel.
    2. Install the upper body side trim panel screw (left side).
    3. Install the jack storage cover (left side).
    4. Install the end gate or liftgate opening sill plate.
    5. Install the rear seat belt lower anchor nut (two door models only). Tighten to 59 ft. lbs. (80 Nm).
    6. Install the upper and lower front seat belt anchor bolts. Tighten the bolts to 52 ft. lbs. (70 Nm).
    7. On two door models, install the rear seat upper seat belt anchor bolts. Tighten the bolts to 52 ft. lbs. (70 Nm).
    8. Install the roof rear header garnish molding. Attach the cargo lamp electrical connection, place the trim in position and engage the molding retainers.
    9. On four door models, install the body lock pillar trim panels.
    10. Install the windshield garnish moldings. Place the molding into position, align the retainer clips with the slots and press into place.
    11. Place the sunshade retainer in position, install the screw and tighten to 10 inch lbs. (1.1 Nm). Position the sunshade, install the screws and tighten to 10 inch lbs. (1.1 Nm).
    12. Install the coat hooks and the assist handles.
    13. If equipped, install the dome lamp.
    14. If equipped, install the overhead or sunroof console.
  2. Install the sunroof opening trim. Start the trim in the center of the front of the sunroof opening and work around the perimeter.

Hope helps (remember rated this) Good luck.
Read full answer
Jun 03, 2010 • 1999 Chevrolet Blazer
0helpful
1answer

Need to remove driver side door panel?
  1. Disconnect the negative battery cable.
  2. If equipped with an accessory switch panel, carefully pry the switch panel up and away from the door panel. Tag and disconnect the switches from the panel.
  3. On 1981-86 models, remove armrest attaching screws.
  4. On 1987-96 models, remove the retainer screws secure the pocket in the molded armrest on the door panel.
  5. If equipped with crank type windows, remove window crank handle with the appropriate clip removal tool.
  6. If equipped with manual remote mirrors, remove the control knob bezel.
  7. Remove inside door handle cover attaching screw and trim plate.
  8. If equipped with door mounted speakers, remove the speaker, and disconnect the speaker wires. For speaker removal and installation steps, refer to .
  9. Remove all external screws securing the door panel. Insert an appropriate prytool between the door panel and door frame to remove the hidden clips securing the panel.
  10. Holding door panel vertical lift straight up to release the upper clip.
  11. Inspect all retaining clips and replace any broken or missing pieces.

To install:
  1. Position the door to the door and carefully press on the retainer clips to engage. If a clip will not engage, inspect the mounting hole behind the panel to make sure the clip is properly aligned. Install any panel-to-door retainer screws.
  2. If equipped with crank windows, attach the washer and crank to the window regulator stud.
  3. On 1981-86 models, attach the armrest to the door using the retainer screws.
  4. On 1987-96 models, insert the armrest pocket and secure in place with retainer screws.
  5. If equipped with door panel mounted speakers, attach the speaker wires to the speaker and secure the assembly to the door panel.
  6. If equipped with remote cable mirrors, attach the control knob to the door panel with the retainer bezel.
  7. If equipped with an ashtray, insert the holder assembly, and secure in place with retainer screws. Install the ashtray to the holder assembly.
  8. Position the door handle trim panel around the door handle assembly, and secure in place with the retainer screw.
  9. If equipped with accessory switch panel, attach the harnesses to the switches, and press the accessory plate into the door panel.
  10. Connect the negative battery cable.
  11. Check and make sure all panel components function correctly.
Read full answer
Apr 03, 2010 • 2002 Ford Explorer Sport Trac
0helpful
1answer

How to remove door panel for driver and passenger side doors
Hi. This Guide will help you with this issue.



Step1 Check out how the door panels are attached to the car. Most panels use screws and bolts but others have snap-in fittings. Gather all the tools you need for removing the door panels. If the panel is attached with screws and bolts, you need a screwdriver or ratchet and socket. Car door panels with snap-in fittings are easily removed with a flathead screwdriver. Step2 Locate where the screws and bolts are before starting. These are usually found in the arm rest area, along the bottom or sometimes near the door lights. Step3 Roll down the car door window. Begin removing all screws and bolts that hold the door panel onto the car. If your car has snap-in fittings, pry gently on the bottom corner of the door panel until the fittings pop out. Step4 Remove the power window control panel if your car has power windows. The control panel should pry out easily, and then you unplug the wiring harness from the back and place it to the side. Step5 Use an L pick and flashlight when locating a manual window crank. Look behind the window crank and slide the pick under the edge of the metal clip that holds the crank in place. Remove the clip and pull the crank off. Step6 Remove the door handle by unscrewing the small screw located in the center. Gently pull the door handle out until you see the back of the handle and unclip the rod from the door handle. This should remove the handle unless the handle and door lockmag-glass_10x10.gif are attached, then you just unclip the rod from the lock and remove them both together. Step7 Unscrew the cap off rear upper corner door panel locks. These don't have a rod attaching them to the handle and unscrew separately from the door handle. Step8 Pop the door panel off after you've removed everything. Gently pry on the bottom edge of the door panel until it releases. Pull out and up to completely remove the door panel.


Please rate and have a great day:)

Read full answer
Mar 25, 2009 • 2002 Kia Optima
0helpful
2answers

Driver door latch opens outside only
From the interior side, remove any screws for the armrest, door panel itself, remove window and door and handle if equipt. Remove door strap if present...pop loose the door panel trim or "door panel" and carefully remove without damaging the inside window weatherstripping.
Read full answer
Mar 12, 2009 • 1991 Mercury Cougar
6helpful
2answers

Driver side power window stopped working
The door panel is held on by plastic clips and 5 screws. 3 screws are on the bottom and 1 in the pull cup and 1 in the inner door handle.Then grab one of the corners and give a small tug, when you get some of the clips to pop out then proceed around the whole panel. To replace the panel take the clips out of the door with a fork and slide them back into the panel and then line it up on the door and use your hand like a hammer and bang the panel back on. Hope this helps
Read full answer
Jan 12, 2009 • 2004 Chrysler Sebring
Not finding what you are looking for?

View Most Popular

1974 Eldorado

  • Cars & Trucks

Related Question

Remove glove box volvo 850 1997

  • 1997 Volvo 850

Related Topics

64 views

Ask a Question

Usually answered in minutes!

Popular Questions

HOW DO I DISABLE ANTI-THEFT SYSTEM CAR WONT START

1999 Cadillac Eldorado

Replacing spark plug wires on a 1981 cadilac

1980 Cadillac Eldorado

How to fix code p1258 on cadillac

1998 Cadillac Eldorado

Starter disabled due to theft system

1995 Cadillac Eldorado

Color codes wiring for delco bose radio

1992 Cadillac Eldorado

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Cadillac Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Sean Wright
Sean Wright

Level 3 Expert

2045 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...