Question about 2001 Ford Explorer Sport Trac

Open Question

Hot wire a ford explorer sport trac - 2001 Ford Explorer Sport Trac

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
chuck943
  • 783 Answers

SOURCE: 2007 FORD EXPLORER SPORT TRAC 4X4 Change oil light on

Press and hold the SELECT/RESET
control switch to select SYSTEM
CHECK when “SYSTEM CHECK /
HOLD RESET” is displayed in the
message center. Selecting this
function from the SETUP MENU
causes the message center to cycle through each of the systems being
monitored. For each of the monitored systems, the message center will
indicate either an OK message or a warning message for two seconds.
Pressing the SELECT/RESET control switch cycles the message center
through each of the systems being monitored.

The sequence of the system check report and how it appears in the
message center is as follows:
1. OIL LIFE RESET
2. CHARGING SYSTEM
3. WASHER FLUID
4. DOOR AJAR
5. EXTERIOR LAMP
6. BRAKE SYSTEM
7. PARK BRAKE
8. MILES TO EMPTY
9. FUEL LEVEL LOW (will only display if 50 miles or less to empty)
To reset the oil monitoring system to 100% after each oil change
[approximately 5,000 miles (8,000 km) or 180 days] perform the
following:
1. Enter SYSTEM CHECK to display
“OIL XXX% RESET IF NEW”.
2. Press SELECT/RESET control
switch to display “HOLD RESET IF
NEW OIL”.
3. Press and hold the
SELECT/RESET control switch for
more than 2 seconds. Oil life is set
to 100% and “OIL CHANGE SET TO
100%” is displayed.

Posted on Apr 02, 2009

Ad
  • 12 Answers

SOURCE: how to change fuel filter on 2001 ford explorer

it in the tank so your gonna either gonna have to drain the tank and lower it to the ground,it shouldn't take more than 30 minutes.make sure you put the seal back in right,so it won't leak,it aint very hard.

Posted on Jul 12, 2009

  • 1 Answer

SOURCE: 01 ford explorer sport trac rear timing chain diagram

They will not loan you the tools.....how else will they continue to rip off the average garage junkie and make lots of money?

Posted on Nov 18, 2009

  • 18 Answers

SOURCE: how do i reset the check engine light on my 2003

Unplug the battery for about 10 min then plug it back up start the engine. the computer should reset, if the light comes back on then u still have problems.

Posted on Jan 07, 2010

Molson02536
  • 3854 Answers

SOURCE: where is the fuel filter location on a 2001 ford

It is inside the left frame rail below the drivers door, you need a special tool to release the filter from the line. filter just snaps into its metal holder. Good luck and you can get the fuel line quick release tool at most Auto Parts store.

Posted on Mar 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace headlight bulb on 2007 ford explorer sport trac


How To Install Replace Headlight Ford Explorer Sport Trac ...

? 4:28
https://www.youtube.com/watch?v=NzMVcCsZ860
May 11, 2010 - Uploaded by 1A Auto Parts
How To Install Replace Headlight Ford Explorer Sport Trac 01-05 1AAuto. .... We offer the replacement headlights on our website for your truck.

Jan 11, 2016 | 2007 Ford Explorer Sport Trac

1 Answer

Where is the oil level supposed to be on the dipstick on a 2007 Ford Explorer Sport Trac I want to make sure I haven't over filled my transmission


There is an opperating range on the dipstick add and xxxxxxx as long you are not below add cold .
If its hot then you have a hot mark the fluid expandes with heat so its higher on the dipstick.
So depending if its hot or cold you should be in the xxxxxx range and the fluid is red and dosn't smell burnt your OK .

Apr 22, 2015 | 2007 Ford Explorer Sport Trac

1 Answer

2001 ford explorer sport trac no pulse on cylinder 4 and a cam code p0340


You have grounded wiring or a bad Driver
in the PCM-- if it comes on when you put battery
voltage to it

Mar 05, 2013 | 2001 Ford Explorer Sport Trac

1 Answer

Fuel gauge on ford explorer sports trac won't move


might want to take a look at the wires that come out of the fuel tank and the fuel pump. also might want to check the fuses

Jan 15, 2013 | 2002 Ford Explorer Sport Trac

1 Answer

Up and down movement on rear axle 2001 ford explorer sport trac


how do i pull out rear axle from my 2001 ford explorer sport trac

Jul 04, 2012 | 2001 Ford Explorer Sport Trac

1 Answer

2001 ford explorer sport trac wont start all the function turn on


check what the diagnosis machine will give if there is no data then check if the starter crank sensor is getting any power

Jul 26, 2010 | 2001 Ford Explorer Sport Trac

1 Answer

Ford explorer and ford explorer sport trac same exterior parts?


Above is correct, some body panels are interchangeable some aren't...Headlights, front fenders, hood yes. Doors unsure, bed and back no (obviously). The underpinnings (suspension) are similar, but not exact...and depending on the year, the Explorer went to independent rear suspension, while the sport trac kept the solid axle differential.

May 15, 2008 | 2006 Ford Explorer Sport Trac

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...