P0604 code po62f p0763 - 2006 Chevrolet Cobalt

P0763 MERCEDES-BENZ Shift Solenoid 'C' Electrical

www.autocodes.com > p0763_mercedes-benz

The P0763 code is detected when the gear required by the ECM does not match the actual gear when vehicle is driven. Possible Symptoms. Engine Light ON (or ... Missing: E430 ‎saying

Diagnostic Trouble OBD Code P0763 - PartsAvatar.ca

partsavatar.ca > p0763-obd-ii-trouble-code-shift-soleno...

The trouble code P0763 can be defined as Shift Solenoid C Electrical. This diagnostic fault code is a generic powertrain code, which means that it would apply to ... Missing: 2001 ‎Mercedes ‎E430 ‎saying

Mercedes Fault Codes and What They Mean - Burdi Motorworks

burdimotors.com > 2017/12/26 > common-mercedes-fa...

Dec. 26, 2017 - Common Mercedes Fault Codes That Trigger Your Warning Lights. Posted on Last updated ... P0763, Shift Solenoid C Electrical. P0764, Shift ...

P0763 Shift Solenoid C Electrical - OBD-Codes.com

www.obd-codes.com > ...

The purpose of the Shift Solenoid Circuit is for the PCM to monitor the shift solenoids to manage the movement of fluid between various hydraulic circuits and ...

https://www.autocodes.com/p0604.html

EMC self check fault yes it can cause a no start problem the following link will help with your code
P0604 Bmw ECM Self Check Fault

P0444, Evaporative Emission System Purge Control Valve Circuit Open". I believe this (small) valve is located underneath the intake manifold behind the oil filter housing. Since there are other codes that indicate leaks in the evap system, you might have to replace the PCV, P0604 could be the coolant level, or a stuck thermostat, top up the coolant, or replace thermostat would be advisable.
hope tis helps

Hi there:

P0604 - GM
Type: Powertrain Computer and Auxiliary Outputs - ISO/SAE Controlled
Description: Control Module Random Access Memory Fault Conditions
Cause: Key on for at least 5 seconds, system voltage over 10v, then the PCM detected that the internal data test (RAM) failed • Refer to code repair chart for instructions on how to replace a PCM and how to reprogram the replacement
This code is a fairly simple one. It basically means that the PCM/ECM (powertrain/engine control module) has detected an internal integrity fault in the PCM.

Hope this helps.

P0763 - Shift Solenoid C Electrical
Possible causes- Faulty shift solenoid C valve
- Shift solenoid C valve harness or connectors
- Shift solenoid C valve circuit is open or shorted
- Low transmission fluid level
- Dirty transmission fluid
When is the code detected?The P0763 code is detected when the gear required by the ECM does not match the actual gear when vehicle is driven.Symptoms- Engine Light ON (or Service Engine Soon Warning Light)
- Transmission will not shift gears.P0763 Description Shift solenoid valve C is turned ON or OFF by the Transmission Control Module (TCM) in response to signals sent from the park/neutral position (PNP) switch, vehicle speed and Engine Control Module (ECM) (throttle opening). Gears will then be shifted to the optimum position.

P1600 - Loss of KAM (Keep Alive ECM memory) Power; Open Circuit

Check all fuses related to the ECM

P0734 A/T Gear 4 Improper Ratio.
P0604 Internal Control Module RAM Error.

are you sure about the last code???

p0128 is coolant temperature sensor below range, change sensor. p0604 is pcm random access mem ( ram error. it may mean the pcm has failed, have it checked out..

if it's like a chrysler 2001 seabring V6 ...P0604 is a failure with the internal transmission control module.

I have bad news for you
p0604 is a transmission control module

check the connection at the transmission control module if there are no connection issues than you will need to replace the transmission controll module "tcm" there is no other test for that code.

good luck

[email protected]