Question about 2000 Nissan Xterra

Open Question

How to pull a 2000 nissan xterra engine - 2000 Nissan Xterra

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Torque and sequence to Intake Manifold for 3.3L Nissan Xterra 2000

Hi El Faraon,
I believe that you're dealing with 12 mm bolts and nuts....THESE ARE NOT THE SPECS FOR YOUR ENGINE, but I believe that if you use them you'll be close....Tighten in three stages up to 22nm....choose the bolts from the centre of the manifold and circle outwards until you reach the last one.....It may be a good idea to draw an overhead or plan view of the unit, marking out the bolt positions.....Start at the centre and mark the sequence and follow that....What is important is starting at the centre, so that nothing becomes warped....

Hope this helps,

Regards, Johngee10

Posted on Sep 06, 2008

Ad
  • 1 Answer

SOURCE: nissan xterra 01

the fuel cap is broke i change that it.

Posted on Oct 13, 2008

  • 6 Answers

SOURCE: 2000 nissan xterra hesitating when engine is warm

We are having the same problem. We are right now changing the crankshaft position sensor along with the intake and manifold gaskets.

Posted on May 14, 2009

TwinTurboZ
  • 78 Answers

SOURCE: 2000 Nissan Xterra Service Engine soon indicator is always on

The knock sensor is not a huge deal to replace and will not turn on the light. It should be dont though.

The crankshaft sensor is located directly between the engine and transmission. It is dead center at the bottom.

Posted on May 21, 2009

HyeProfile
  • 35 Answers

SOURCE: 2000 nissan xterra knock senor and plug 5

Change your oxygen sensor. They're due...

Posted on Aug 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am replacing the distributor on a 2000 nissan xterra v6cyl 4wd my question is how to tell if i have the #1 piston in the up position


Pull # 1 spark plug, install compression gauge or somehow block hole and jog engine until you feel or record compression, then line up TDC marks on crank pulley. Now when you drop distributor in, rotor should line up with # 1 spark plug wire tab under cap. Make sure you have all ignition spark disconnected, one way or another. If you haven't pulled other distributor yet, it should be easier, just mark housing for reference, jog until rotor is at # 1 tab, remove old one and re-install new in same position.

Apr 11, 2010 | 2000 Nissan Xterra

2 Answers

The power outlets dont work in my 2000 Nissan


Check fuses located at driver's left dash area and under the hood.

Feb 09, 2010 | 2000 Nissan Xterra

2 Answers

Does my 2001 3.3L V6 EFI Nissan Xterra have a non


It's has a timing belt, also it's an interference engine, if belt goes bad it will bent valve's .

Nov 24, 2009 | 2000 Nissan Xterra

1 Answer

Where is the knock sensor for the 04 nissan xterra located?


Your knock sensor is located undernesth the air intake manifold on top of the engine block. This goes for 2000-2004 xterra V6 3.3L models.

Nov 05, 2009 | 2002 Nissan Xterra

1 Answer

000 NISSAN Xterra -- after warming up, loses RPM by 500-1000..... have replaced ignition wires and distributor, checked mass air flow sensor and OK.....


I had a problem on my Nissan Xterra 2000. Symptons sound similar. In my case, it ran fine for a while and then suddenly the engine starts to stumble and lose output. At one point it did not even have enough HP to move. Irregular idling too. Thought it was water in my fuel. Bought water remover from the store and added to gas tank. Problem did not go away. Instead, "Service Engine Soon" light came on. Had to have it towed to the dealer as there was no way the engine could keep up with traffic. Dealer replaced the "Crank Position Sensor" today. Parts $33.00, Labor: $300 (about 3 hrs worth of work). Seems to work fine now but I will wait and see. Dealer also stated that Distributor bearing appears to be noisy and will need to be replaced sooner or later. I will wait for it to go before I fix that.

May 22, 2009 | 2000 Nissan Xterra

1 Answer

2000 Nissan Xterra Service Engine soon indicator is always on


The knock sensor is not a huge deal to replace and will not turn on the light. It should be dont though.

The crankshaft sensor is located directly between the engine and transmission. It is dead center at the bottom.

May 17, 2009 | 2000 Nissan Xterra

1 Answer

2000 nissan xterra hesitating when engine is warm


We are having the same problem. We are right now changing the crankshaft position sensor along with the intake and manifold gaskets.

May 09, 2009 | 2000 Nissan Xterra

Not finding what you are looking for?
2000 Nissan Xterra Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...