What is the torque spec for the head bolts on a 1993 dodge ram 50 w/ 2.3 l

What are the torque specs for the rod bearings on a 2006 - Fixya

https://www.fixya.com > ... > 2006 Dodge Caravan
Nov 15, 2019 - What is the torque specification for the inner tie rod 1996 .dodge caravan 2.4 liter. 45-55 foot pounds. Read full answer. Sep 18, 2012 • 1998 ...
SOLVED: Torque chart for dodge caravan 4l - Fixya
Sept 9, 2019
Main bearing torque spec for Dodge Grand Caravan 2005
Sept 15, 2019
Im trying to find the connector rod bearing torque - Dodge - Fixya
Jul 15, 2018
Head bolt torque specs for 2.4L dohc dodge caravan - Fixya
Jun 2, 2012
More results from www.fixya.com

Dodge Caravan 2.4 need engine tightening specs and head ...

https://www.justanswer.com > chrysler > 28qv6-dodge-...
Jun 27, 2009 - SPECIFICATIONS - TORQUE ; Balance Shaft Carrier Cover-Bolts, 12, - ; Camshaft Sprocket-Bolt, 101, 75 ; Connecting Rod Cap-Bolts, 27 +¼ turn, 20 +¼ ...
1 answer · Top answer: Here are the head bolt specs: Before installing the bolts, the threads should be coated with ...

Torque Specifcations - MAHLE Aftermarket

https://www.mahle-aftermarket.com > media > torque3
PDF
Engine Model Year. Rod Torque. Main Torque. Cylinder Head Bolt Torque. CASE. 2.4. 148. 61-66. 45-50 FT/LBS. 90-100 FT/LBS. 60-65 FT/LBS. CASE. 2.4.
124 pages
You've visited this page 3 times. Last visit: 01/02/22

Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:

1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
2. Step 2: Bolts 1-10 verify torque without loosening
3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)

1. 2.7 litre intake bolt torque spec in a 2008 dodge charger ...

   www.fixya.com/cars/t18664111-2_7_litre_intake_bolt_torque_spec_in Jun 27, 2013 - Head Bolts Step one 37 ft lbs then tignten 120 degrees more. Rocker arms. Step one 11 ft lbs then tighten 90 degresss more. Upper intake 89 inch ...

Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

STEP 1 TORQUE BOLTS 1 - 8 - 35 FT LBS STEP 2 TORQUE BOLTS 1 - 8 - 50 FT LBS STEP 3 TORQUE BOLTS 1 - 8 -50 FT LBS STEP 4 TORQUE BOLTS 1 - 8 - PLUS 1/4 TURN STEP 5 TORQUE BOLTS 9 - 11 21 FT LBS.

For 2004 Dodge Stratus 2.4L SFI SOHC 4cyl the Head Bolt Torque sequence
------------ | 10 6 2 3 7 | | 9 5 1 4 8 | ------------

Step: 1 - Torque to 25 ft/lbs
Steps: 2 - Torque to 50 ft/lbs
Steps: 3 - Torque to 50 ft/lbs
Steps: 4 - Turn 90 degreesRecheck final torque in sequence

Caution:Engine uses torque to yield head bolts (TTY) that permanently stretch during initial installation. New head bolts must be used when cylinder headis replaced or re installed to obtain proper torque specification.

Hope helps (remember comment and rated this).

Cylinder Head Bolts (1st Step) 68 N·m (50 ft. lbs.) Bolts (2nd Step) 143 N·m (105 ft. lbs.)

Cylinder Head Bolt 5.9L

Step 1 - 50 ftlb
Step 2 - 105 ftlb
Step 3 - Recheck At 105 ftlb

Tightening sequence

Rocker Arm Bolt

5.9L - 17 ftlb

Cylinder head bolts for 2.4 doch in ft\lbs
Step 1 .....................................................................................25
Step 2......................................................................................50
Step 3.......................................................................................50
Step 4.....................................Tighten an additional 1/4 turn (90-degrees)


the order is shown in this image:http://yfrog.com/2ocylinderheadj

1. For 1.8L engines, tighten the bolts in sequence, as follows:
   1. Step 1: Bolts 1-10 to 22 ft. lbs. (29 Nm).
   2. Step 2: Bolts 1-10 to 43 ft. lbs. (59 Nm).
   3. Step 3: Loosen bolts 1-10 completely.
   4. Step 4: Bolts 1-10 to 22 ft. lbs. (29 Nm).
   5. Step 5: Bolts 1-10 plus 50-55 degrees.
   6. Step 5: Bolts 11-14 to 74 inch lbs. (8 Nm).
      
      Fig. Cylinder head torque sequence-1.8L engine
      
      
      Fig. Tighten the valve cover bolts in sequence-1.6L and 1.8L engines