Question about 2002 Dodge Neon

1 Answer

2002 dodge neon code p0750 & p0706, it is limp mode and with not upshift, with snap -on scanner trans temp is 1024 deg f, and always in neut.

Posted by on

  • bbenson283 Dec 02, 2008

    I know where the solenoid is, but I dont know or see where the range sensor is. Is this inside the transmission.

  • Anonymous Mar 16, 2014

    98 dodge 2500 4whl drive trans in limp mode


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 260 Answers

Im not a trans. expert but would verify the range sensor (gear indicating sensor) is working properly and the L/R solenoid is ok. those are the 2 suspects for your problem

Posted on Dec 02, 2008

  • autodr
    autodr Dec 02, 2008

    although you can access the electrical connector for range sensor externally, you must remove trans valvebody to service. also this range sensor has an integrated temperature sensor in range sensor itself. this sensor may take care of both problems. keep me posted, curious to see end result. i do not rec. removing valvebody unless pretty experienced.


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

4 cyl. Auto trans. in limp mode. takin the shift solenoid out to re build it i fnd ripped wires. My question may seem should i re connect the first or cont with the shift solenoi

Unfortunately, you should have gotten the diagnostic codes for the transmission before messing with the shift solenoid. Most of those dodge shift issues are caused by input and output speed sensors.

Feb 09, 2016 | 2002 Dodge Neon

1 Answer

1991 tcm dodge dynasty where is it on the car will not shift out of 2 gear

you trans is in limp in mode usually caused by sensors on that model, input and output sensors in trans, but you need to determine that before you replace anything, use a scanner to read the codes then go from there

Oct 30, 2015 | Dodge Cars & Trucks

1 Answer

2002 neon tranny probs...spedo doesn't work..changed both input and output speed sensors, trans in limp mode obd2 codes 1698 and 500

the sensor magnet wheel in the output shaft of the tranny can be sliiping on the shaft but!! due to it being a 2001 model you more than likely ahve internal clutch pack issues and bad worn or burnt clutch disk that tranny will not perform with severe internal damage

Jan 21, 2010 | 2001 Dodge Caravan

1 Answer

2003 dodge neon only runs in first gear slips at 1500 rpm , must shut car off an turn on for it to run , wont shift out of first.runs fine in it a pcm problem.

No,Your car is in "limp"mode,
there are three sensors on the transmission that tell the computer how fast your going so it knows to upshift,
have someone check input sensor,output sensor,and speed sensor.

Jan 14, 2010 | 2003 Dodge Neon

1 Answer

1997 dodge caravan shifting problems have codes p700 and po750

p0700 is indicating a trans fault present..p0750 is low-reverse solenoid circuit..most likely defective solenoid pack on front of transmission..300-400 dollar part

Jun 10, 2009 | 2003 Dodge Neon

1 Answer

Limp mode?

It may have a "loss of prime" code that usually follows a service of the fluid and filter. After you're sure the fluid is full at operating temperature, disconnect the battery for a few minutes and reconnect to see if the code resets. I hope this helps.

Apr 26, 2009 | Dodge Intrepid Cars & Trucks

1 Answer

95 dodge intrepid wont shift out of first gear

It sounds like the trans has gone into "Limp In" mode. You may need to access the trans controller and look at fault codes. A Generic OBDII scanner may give you the codes. You could also try disconnecting the battery which will reset the trans controller. (however that is not a cure but it will verify the trans was in fault mode) The most common issues I've seen have been with the "Input" and "Output" Turbine Speed Sensors. They are both mounted on the trans case (External). The input is towards the front and the output is near the rear.

Mar 30, 2009 | 1999 Dodge Intrepid

1 Answer


Transmission Control System Malfunction.It means you have a trans control problem in the trans computer.
You will need to get it on a trans capable scanner to see what the trans code or problem is. You should get it to either the dealer or a good transmission shop to the the trans capable scanner done to see the exact problem

Feb 08, 2009 | 1999 Plymouth Voyager

1 Answer

Transmission won'shift out of low gear

more than likely it is a trans speed didnt say if the check engine light is on but i am assuming it is. the input or output sensor failing will put the trans into limp in mode

Sep 21, 2008 | 2002 Dodge Neon

2 Answers

Limp in mode

you have to change the solenoid control if your car is 3.5 engine the solenoid control located at inside the transmission..

Aug 19, 2008 | 2004 Dodge Intrepid

Not finding what you are looking for?
2002 Dodge Neon Logo

Related Topics:

586 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6864 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides