Question about 2000 Ford Taurus

Open Question

Change passenger side front fender 2000 ford taurus

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

c17hydro
  • 2984 Answers

SOURCE: 2000 Ford Taurus. How do I change a ball joint?

Lower Ball Joint Inspection

  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Raise and support the vehicle.
  3. Prior to carrying out any inspection of the ball joints inspect the wheel bearing.
  4. Have an assistant pull inward and outward on the top and the bottom tire. Mount a suitable dial indicator and measure the movement between the ball joint and the lower arm. If the movement is at or exceeds 0.03 in. (0.75 mm) install a new ball joint.
167f4af.gif

Removal & Installation To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Remove the knuckle from the front suspension.
  3. Remove the snap ring from the ball joint.
  4. Press the ball joint out of the knuckle with a suitable ball joint press and adapters.
656c3d7.gif

Posted on Jul 04, 2009

  • 691 Answers

SOURCE: Need to replace passenger side front fender.

just used standard sockets with extenson, screw driver and phillips, remove head light and fender and fender guard cover. helper would really come in handy, so you dont scratch or drop fender.

Posted on Jul 12, 2009

solasknows
  • 199 Answers

SOURCE: Front Passenger seat belt on 1996 Ford Taurus will

inside the plastic cover there is a spring mechanism, check that the spring might have came out of its place

Posted on Jul 23, 2009

  • 70 Answers

SOURCE: 2000 Ford Taurus: With heavy rain, water leaks

if you can remove the plastic "cowl" section(s) at the base of the windshield and clear out any debris.sticks,dirt,acorns,mud,etc. THEN run a garden hose where the rain normally would run down and "flush"the drainage paths at each end by each fender. see if that fixes the problem. theres also a possibility that the windshield seal could be bad.

Posted on Aug 31, 2009

  • 6 Answers

SOURCE: How do I change the turn signal bulb on 2000 Ford Mustang

Actually its easier that what the other guy said. lift your hood, look at the headlight there will be two rods that u can pull on the top of the light where it sits in the frame. pull those and u can then pull your headlight out, that will make it alot easier to get to.

Hope This Helps.

Posted on Sep 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I am trying to find out what is making my front end grind on passenger side when i drive down the road on 2000 ford taurus


Check the front brake rotor. When the brake pads wear down too far they will make a grinding noise. I am not sure what sound the axle makes when they begin to wear out. I would check the boot that covers the axle joint for any damage.

Apr 17, 2015 | 2000 Ford Taurus

2 Answers

Where is the low pressure port ?


That port would be located at the rear of the passenger side fender well under the hood. It's kind of against the firewall. Be carefull of moving parts as the front of the engine is right there. Good luck

Jul 10, 2014 | 2002 Ford Taurus

1 Answer

Where the computer engine in a 2000 ford expedition


a '97 XLT with the 4.6 ECU is located on the passenger side by the fuel & air suspension cut-off switchs. It is just in front of the passenger side front door mounted to that fender - its not to hard to find once you know what you are looking for and if you use a flashlight.

Jan 15, 2011 | 2000 Ford Expedition

2 Answers

Firing order diagram ford taurus v6 3.06 6 cylinder engine, and which one is the number 1


FIRING ORDER IS 1 4 2 5 3 6. STANDING IN FRONT OF CAR ON PASSENGER SIDE FIRST CYLINDER FRONT IS 1 2 3 ON DRIVER SIDE FIRST CYLINDER FACING YOU ARE 4 5 6 SEE 1 CYLINDER FACING YOU ON PASSENGER SIDE.GET A PIECE OF PAPER WRITE NUMBER ON TOP ACROSS LARGE NUMBERS 3 2 1 AND BOTTOM OF PAPER WRITE NUMBERS 4 6 5 THATS COILS WIRES FIRING ORDER TO SPARK PLUGS.

Sep 26, 2010 | 2000 Ford Taurus

1 Answer

Wheres the belt tensionor on '99 ford taurus 3.0 ohv


Facing the belt from the passenger side front fender, the lowest pulley that the belt rides on is the crank shaft, the belt tensioner is just above and to the right of the crank shaft. It doesn't have ridges that the belt rides in because the backside of the belt is what rides on the tensioner.
I hope this was helpful.

Jan 16, 2010 | 1999 Ford Taurus

3 Answers

Where is the no. 1 cylinder on a 1992 Ford Taurus v-6?


Cylinder Numbers on the V-6 Ford Tourus

Passenger to driver side on firewall side1-2-3
passenger to driver side on Radiator side 4-5-6

Firing order 1-4-2-5-3-6

Good luck

Dec 09, 2009 | 1992 Ford Taurus

2 Answers

Coolant leak front passenger side leaking anti freeze over right front fender well can not see leak


the coolant resvoir bottle is located above that fender well it's possibly has a small crack in it i just fixed one the other day

Oct 23, 2009 | 2003 Ford Taurus

1 Answer

2000 Ford Taurus: With heavy rain, water leaks into cabin filter holder, down air vent, and onto passenger side floor. This just started happening this spring. Are there drain holes somewhere I should...


if you can remove the plastic "cowl" section(s) at the base of the windshield and clear out any debris.sticks,dirt,acorns,mud,etc. THEN run a garden hose where the rain normally would run down and "flush"the drainage paths at each end by each fender. see if that fixes the problem. theres also a possibility that the windshield seal could be bad.

Aug 31, 2009 | 2000 Ford Taurus

1 Answer

Need to replace passenger side front fender. I have new front fender, it is painted and ready to be installed. Are there any special problems or tools needed?


just used standard sockets with extenson, screw driver and phillips, remove head light and fender and fender guard cover. helper would really come in handy, so you dont scratch or drop fender.

Jul 07, 2009 | 2000 Ford Taurus

2 Answers

Misfire on cylinder 6 on a 2002 ford escape 3.0 6 cylinder DOHC


the back side is from front(passenger side) of engine 1,2,3
front side is 4,5,6

Mar 17, 2009 | 2000 Ford Taurus

Not finding what you are looking for?
2000 Ford Taurus Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...