Tip & How-To about Acura CL

Acura How To Restore Electric Window One Touch Control

If you have disconnected the battery for any reason on your Acura you will find that the one touch control feature on your electric windows no longer operates.

You can resolve this by following this very simple procedure to reset the one touch control feature and get it operating again thereby saving you a trip to the dealer!

1) Start the engine and then push down on the drivers window switch until the window is fully open.

2) Pull up the drivers window switch until the window closes fully but keep holding the switch for at least 2 seconds after it closes.

3) Auto function should now be restored. Lower and raise the window to check the one touch control.

Hope this tip has helped. Please do leave a vote for it. Many thanks.

Posted by on

Cars & Trucks Logo

Related Topics:

Related Questions:

1 Answer

99tl Acura is there any other reason battery won't charge if alternator is good


the battery is no longer good and can no longer hold its charge, example, u need to boost ur car in the morning but then ur fine through out the day, car sits over night thus loosing its charge and needs to be boosted again

Jan 24, 2017 | Acura Cars & Trucks

1 Answer

Pulled battery terminal on Chrysler 300c 2006. After reconecting , the power windows no longer go up automatically


If your vehicle is equipped with the "Express-Up" feature, the door module probably lost its calibration when the battery was disconnected. To recalibrate this feature, roll the windows all the way down. Then hold the button to the up position. Continue to hold the button up for two seconds after the window has reached the full up position. Roll the window down again and repeat this a second time. The express-up feature should now work for that window. Repeat this procedure for the other front window.
NOTE: the REAR windows are NOT EQUIPPED with this feature.

May 11, 2011 | 2007 Chrysler 300c AWD Sedan New Cars

1 Answer

i want to remove passenger side rear door panel because window is down and won't stay up


Hi,
Hi!!

Here is a little information on how window regulator works. Also step by step instruccions on how to remove and install the window glass.

Door Glass & Regulator Power Windows
Diagnosis & Testing
When the rear window lockout feature is enabled, the circuit is open and no voltage is supplied to the rear window switches. When the feature is not enabled, the circuit is connected to battery positive voltage. If this circuit is shorted to ground when the lockout feature is not enabled, the PWR WDO circuit breaker may cycle continuously OFF/ON until, either the lockout switch is pressed to open the circuit, or the circuit breaker is permanently damaged. All windows may be partially or totally inoperative while the fault is present.
Inspect for aftermarket devices which could affect the operation of the system. Inspect the easily accessible or visible system components for obvious damage or conditions which could cause the symptom. Faulty electrical connections or wiring may be the cause of intermittent conditions.
Removal & Installation
Window Motor & Regulator
  1. Position window approximately half way down in the door.
  2. Remove the interior trim panel.
  3. Remove the water deflector.
  4. Tape the window to door frame to prevent it from moving.
  5. Remove the three front door window regulator motor screws.
  6. Disconnect the electrical connector from the window regulator motor.
  7. Remove front side door window regulator motor.
  8. To install, reverse removal procedure.

Window Switch
Front
  1. Remove the front door pull cup screws and pull cup from the front door trim panel.
  2. Disconnect the electrical connectors from the front door power window control switch.
  3. Remove the front door window control switch using a small, flat-bladed tool at the side of the switch.
  4. To install, reverse removal procedure.

Rear
  1. Remove the rear door pull cup from the rear door trim panel.
  2. Disconnect the electrical connectors from the power window control switch.
  3. Remove the rear door window control switch from the pull cup using a small, flat-bladed tool at the side of the power window control switch to release the power window control switch retainer.
  4. Remove the power window control switch from the rear door pull cup.
  5. To install, reverse removal procedure.

Sep 07, 2010 | 2002 Buick Century

1 Answer

removal of the driver seat of my 1988 acura legend


I'm not certain of the layout of the bolts on your particular model, but there should be 4 bolts, one at each end of the seat tracks (the things the seat slides back and forth on), attaching the tracks to the floor. You may need to slide the seat back to access the front bolts, and forward again to get the back ones. Tilt the seat back right forward to allow you to get the seat out the door. If the seat has electric controls there will be some plugs to disconnect under it. If there are any yellow coloured plugs, DO NOT disconnect them without disconnecting the negative terminal off the battery and waiting for 5 minutes. The yellow plug is an airbag system plug, and if the battery is not disconnected the airbags could potentially deploy. Make sure the battery remains disconnected for the entire time that the yellow plug is disconnected, and reconnect the battery AFTER the yellow plug. If there isn't a yellow plug, don't worry.

Hope this helps.

Oct 26, 2008 | 1988 Acura Legend

Not finding what you are looking for?

1,995 people viewed this tip

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Loading...