I cannot locate the bulb in my Panasonic PT61LCX70-K

Purchase a replacement lamp from somewhere like espares or the like.
It should be a standard E17 or SES 20Watt bulb.

We recommend you have an authorized service center location replace the light bulb. Authorized service centers can be found in the below link.

www.panasonic.com/repair
Welcome to Panasonic Online Repair

HI,

Panasonic PT50LC13 lamp indicator blinks to tell you the lamp is faulty.

You need to replace the bulb or TY-LA1000 lamp assembly. This link displays all Panasonic TV Lamps and TV Bulbs. This page shows Panasonic lamp location and How to Replace TYLA1000 bulb. TY-LA1000 Bulb Replacement requires the use of a long Philips Screwdriver to reach screws within the lamp cage.

Unplug AC power before removing the lamp and re-install all doors, etc, correctly before starting the TV. Vacuum any visible dust or lint from air vents and lamp area. Do not used forced air to blow out dust, big problems may result.

The user's manual has a description of what the Blinking LED indicators mean.


Image of TYLA1000 lamp.


Robert

There is a sensor where the door of the bulb is located. You will need to purchase (or by-pass) the door sensor to allow your tv to function again. It is located inside the small hole nearest the screws for the bulb door.




Thank you and please rate!

Hi,

Do you mean you want to replace light bulb for your microwave? If yes follow the instructions below;

1. PLEASE UNPLUG YOUR MICROWAVE!
2. Picture of your microwave with a phone or camera so that you don't forget how to assemble it back.
3. Remove the two screws that holds grill. They are located at the edge of the unit. Once the screws are out, rotate the grill forward from the top. It will pop right out.
4. Once the screws are out, rotate the grill forward from the top. The grill should pop right out.
5. Locate a small access cavity on the left.
6. Remove the screw that is located near the front of the microwave door.
7. Lift up the sheet metal floor to access the bulb. The bulb is located under the sheet metal "floor" on the left.
8. Place a flash light on the microwave floor and shine the light in the light area. This will help you see better when you replace your bulb.
9. Look for a small shiny reflector that hides the bulb. Use your two fingers to squeeze it a bit. Making sure not to bend it.
10. The bulb connection should come right out.
11. After you replaced the bulb, re secure the reflector and the sheet metal floor with the single screw. Test the bulb by plugging in your microwave.
12. Once you see that the bulb works. Unplug your microwave again and re attach the front grill. You are now done.

I hope this helps to solve your problem.

Good luck.

how can change my burnt lamp.

I have replaced my bulb in the housing and it is a tricky process because there are 3 T10m torq screws on the inside of the housing that have to be removed with a very long T10 tork driver as well as 1 on the outside which holds the 2 plastic covers together. 2 screws are located on the same cover which the bulb is located in and the 3rd screw is located on the plastic which has the ancroring screw in. Be very careful not to touch the bulb with bare hands as this will destroy the life of the bulb (always use gloves when handeling the bulb)

on the back on of the tv. either on the right or left side.

Hello, I also have a Panasonic Microwave ( model NN-S 564 or 574 ?) They are very similar.
I have just removed the outer cover 5 screws ( unplug of course ) and have located the bulb holder which is a white plastic component with two clips holding the globe, pull it out and remove the two spade clips connected to the globe. The globe will come away attached to a black plastic mount. Next........do the run around to find someone who sells it.
Perth has an authorized distributer/repairer in Myaree whose details I got from Panasonic. He may sell them. otherwise I will try a couple of specialist light globe suppliers I know....PROLAMPS in Belmont and one in BALCATTA whose name escapes me but I have been there before...Hope this helps others.

Martin

Hi all,

I have just replaced the bulb in my Panasonic NNA873 Dimension 4.

Please be careful,although it was an easy job, there is a capacitor inside which stores heavy loads of power and will release the electricity into you if you touch it!

YOU CANNOT REPLACE THE BULB FROM INSIDE THE MICROWAVE....... DO NOT REMOVE THE CARDBOARD-STYLE COVERING WHICH IS ATTACHED WITH ONE SCREW INSIDE THE MICROWAVE ON THE RIGHT.

To replace bulb will take 5 minutes.

UNPLUG microwave. Remove the outer cover by unscrewing about 6 screws (ordinary phillips) don't lose them into the workings.......

Bulb is located on the right side, nearer to the front. You cannot see the glass of the bulb, only the black plastic end piece, as the bulb sits upside down and vertically. Best if you check out what a T170 looks like on the internet, then you will know what you are looking for. For my Panasonic I needed a T170 (but be careful, they have different ends, some are straight, some right angled - mine was right angled - check before you buy and no, I don't think you can get them from any ordinary supermarket etc!!). Do not touch the bulb when replacing as the oil on your fingers will shorten its life.

Old bulb can be removed by taking out one screw and then pulling off the connectors - there is a little tab to push down to ease them off.

Then simply replace bulb!

When putting cover back on make sure all the tabs on top and sides go inside not outside casing.

Good luck. This is an easy job, just don't poke around anywhere else.