Why is this window motor or window regulator is making noice after i replace the motor

Can be lots of things. If you don't open the door, to see what god on, you won't find out. Could be from a loose screw, to a broken gear or some other things. You have the car close bye an you can look in it. We have to guess. Most guesses will be wrong, an anyway if you want to solve the problem, you have to open the door anyway. Or just bring it to a repaire shop.

You will have to check the voltage of the motor.With the window switch depressed check the voltage at motor.It should give 12 volts.If there is no voltage, then its motor causing the problem.But if there is proper voltage, then its regular causing the problem.Also check and confirm, the window switch is receiving the voltage and switch wirings are intact and not getting loose.In the regulator there are metal brackets, they tend to get bend and this blocks the motor from running.So check the brackets too.If they are bent, then get it straightened.-------------If the regulator checked faulty,worn out bent ten it has to be replaced.-----------

No the window regulator is not going bad in most cases, but to make a final determination of what the cause is, answer this, does the window make any attempt to roll up? if not then the switch is defective, if it does try to move lubricate the window channel's with dry Graphite spray and see if that eases the roll up problem.

Glass & Regulator

1. Lower the window glass and remove the inner handle cover, door lock knob (if necessary), the window regulator handle and the door trim panel.
   

On vehicles with power windows, disconnect the wiring couplings.

1. Carefully peel off the door screen so that it can be reused.
   
2. Replace the window regulator handle and position the door glass so that the door glass installation bolts can be removed from the service hole.
   
3. Remove the door glass installation bolts.
   
4. Remove the door glass. Remove the regulator installation bolts, and then remove the regulator through the service access hole. Remove the window motor mounting bolts and separate the motor from the regulator.
   
5. Installation is the reverse of the removal procedure. If the vehicle is equipped with power windows, connect the leads of the motor to a battery and run the regulator to the down position before installing the motor. Cycle the window several times to make sure that everything is in good working order.
   

hope this helps
plz vote comment if need more help reply

Motor

1. Raise the window glass to the full-up position if possible. If the glass cannot be raised and is in a partially down or full-down position, it must be supported so that it will not fall into the door well when removing the window motor.
   
2. Disconnect the negative battery cable.
   
3. Remove the door trim panel and watershield.
   
4. Detach the window motor harness connector.
   

WARNING

If the front door power window regulator counterbalance spring must be removed or replaced for any reason, make sure that the front door power window regulator arms are in a fixed position prior to removal to prevent possible injury during c-spring unwind.


WARNING

If the front door power window regulator counterbalance spring must be removed or replaced for any reason, make sure that the front door power window regulator arms are in a fixed position prior to removal to prevent possible injury during c-spring unwind.

// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 32; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos';

1. Remove the three window motor mounting screws.
   
2. Remove the window motor.
   

To install:

1. Position the window motor to the power window regulator. Install the three screws snugly but do not tighten all the way.
   
2. Attach the window regulator electric drive wires at the connector and cycle the door window glass to make sure the motor gear engages. After the gears are engaged, tighten the three window motor retaining screws to 54-88 inch lbs.(6-10 Nm).
   
3. Connect the negative battery cable.
   
4. Check the power window for proper operation.
   
5. Install the door trim panel and watershield.
   

// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 32; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos';

you need to raise your window 1st take out nuts holding window regulator manually raise the glass and hold the glass by using tape motor and reail or regulator they come in one piece i beleive/make sure you disconnect the power going to the motor before you take it out

Most probably you need to replace the window regulator...

it sounds to me that the cables have broken. it requires installing new regulators. pretty easy once you get the door panels off. follow the bolts. the window is bolted through sashes to the regulator

you will need to drill out some rivets. Replace with ntus and bolts and washers & lock washers. Make sure they don't hit glass going up and down. Otherwise you will need a heavy duty riveter.
please rate as fixya if this helps.

Motor —Front Door
Special Tool(s) Heavy Duty Riveter
501-D011 (D80L-23200-A) or equivalent
Removal
NOTE: The window regulator and motor are removed as an assembly.

1. Remove the front door trim panel. For additional information, refer to Section 501-05 .

1. Remove the front door radio speaker.

1. Remove the latch remote control. For additional information, refer to Section 501-14A .

1. Remove the front door watershield.

1. CAUTION: Support the window glass to avoid damage.
   Raise and support the front door window glass to the full up position.

1. Disconnect the power window motor electrical connector.

1. Remove the window glass to regulator nuts.

1. Remove the motor and window regulator assembly.
   1. Drill out the rivets.
   1. Remove the motor and window regulator assembly.

1. NOTE: Prior to motor removal, make sure the regulator arms are in a fixed position to prevent counterbalance spring unwind.
   Remove the power window motor.
   1. Remove the bolts.
   1. Remove the power window motor.

1. Raise and support the rear door window glass to the full up position.
2. Remove the interior door handle.
3. Remove the rear door speaker.
4. Remove the water shield.
5. Disconnect the rear door window regulator motor electrical connector.
6. Remove the rear door window regulator rivets.
7. Remove the rear door window regulator by sliding the regulator arms off of the window glass track.
8. Installation is the reverse of the removal procedure, noting the following:
   • Cycle the door glass to make sure of engagement of the drive mechanism.
   • Remove the rear door window glass-to-regulator bolt or rivet.
   • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet.
   • Secure the rear door window glass in the full UP position with tape.
   • Disconnect the window regulator motor electrical connector.
   • Remove the 2 window regulator nuts.
   • Remove the 3 window regulator motor bracket nuts.
   • Install the window regulator assembly. Tighten the 3 motor bracket nuts to 89 inch lbs. (10 Nm).
   • Install the 2 window regulator nuts. Tighten the nuts to 89 inch lbs. (10 Nm).
   • Connect the window regulator motor electrical connector.
   • Remove the tape securing the rear door window glass in the full UP position.
   • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet. Tighten the bolt to 62 inch lbs. (7 Nm), or install a new rivet.
   • Install the window regulator motor
   • Remove the window regulator assembly.

Remove the window regulator motor