1Try my best all the time!
kittyshorty posted an answer for this Video Game Consoles & Games:
"Some games require both ds's to have the same game."
kittyshorty
kittyshorty posted an answer for this 1996 Chevrolet Cavalier:
"There usually not hard to replace. Take off belt, disconnect connector and there should be..."
kittyshortykittyshorty posted an answer for this 1996 Chevrolet Cavalier:
"1996 chevy cavalier alternator replacemant"
kittyshorty
kittyshorty posted an answer for this Chevrolet Cars & Trucks:
"Start by checking for fuses or relays. I think it should be a relay. To check a relay just..."
kittyshortykittyshorty posted an answer for this Chevrolet Cars & Trucks:
"I have a problem with not getting power to my fuel injectors on a 1994 chevy K2500 pickup."
kittyshorty
kittyshorty posted an answer for this 2004 Chevrolet TrailBlazer:
"a/c relay has to do with a/c compressor. Do you have a/c? If so it's not that. You could..."
kittyshortykittyshorty posted an answer for this 2004 Chevrolet TrailBlazer:
"car idols rough and has started over heating had auto zone pull codes and they said it is..."
kittyshorty
kittyshorty posted an answer for this 2000 Mitsubishi Galant:
"fuel pump might be inside the gas tank."
kittyshortykittyshorty posted an answer for this 2000 Mitsubishi Galant:
"where is the fuel pump on the gas tank"
kittyshorty
kittyshorty posted an answer for this Welding Tools:
"Green is ground, white is nuetral, and black is hot."
kittyshortykittyshorty posted an answer for this Welding Tools:
"My Mig welder is a 220v and has 3 wires, white black and green. My question is: witch..."
kittyshortykittyshorty posted an answer for this Miller Welding Tools:
"Can you turn your amps down to 100 and it still melt the tungsten? The hlp 12 code..."
kittyshortykittyshorty posted an answer for this Miller Welding Tools:
"We have problem with our Miller Syncrowave 250 DX Tig welder. On start up it displays..."
kittyshortykittyshorty posted an answer for this Miller Welding Tools:
"If theres a pre or post flow set it will deley gas flow when using a foot pedal or strike..."
kittyshortykittyshorty posted an answer for this Miller Welding Tools:
"No gas flow"
kittyshorty
kittyshorty posted an answer for this Miller Hf 251D 042388 Tig Hi Freq For Engine Driven:
"Make sure you have a good ground. With high frequency you can get it to still arc but have..."
kittyshortykittyshorty posted an answer for this Miller Hf 251D 042388 Tig Hi Freq For Engine Driven:
"The tig welder will arc but there is no amperage and nothing is heated up it acts l;ike..."
kittyshortykittyshorty posted an answer for this Lincoln Welding Tools:
"I'd use 100% argon with a 15cfh for flow and with a 9 second post flow."
kittyshortykittyshorty posted an answer for this Lincoln Welding Tools:
"seting up a ges ranger 305 for 1/4" stainless"
kittyshortykittyshorty posted an answer for this Miller Welding Tools:
"I'm not sure what it's doing to know why it's not working but if I was trying to weld..."
kittyshortykittyshorty posted an answer for this Miller Welding Tools:
"I have a Miller Synchrowave 180 sd and have been having difficulty welding aluminum. Can..."
kittyshorty
kittyshorty posted a question about 2005 Pontiac Grand Prix:
"My car won't start it just clicks. The purple wire going to starter selenoid does not..."
kittyshorty
Welding Tools 6 answers
Cars & Trucks 4 answers
Video Game Consoles &... 1 answer
