Need a wiring diagram for split system heat pump model number ch5536vkc2

No offense but that is a poor excuse for the work not being completed. First, a good tech wouldnt need the diagram. Second, the diagram is likely on the unit or easily available on the internet. Hire a licensed contractor and a reputable company!!

Hi,
could you provide the exact model number or the product you need the wiring diagram for



Thanks
Proton

Omg. Outdoor wiring diagram for what???? Lawnmower, vehicle, tractor, well pump, sprinkler system, condenser, heat pump, generator...WHAT MAKE?? WHAT MODEL?? WHAT??

If you need further help, reach me via phone at https://www.6ya.com/expert/thomas_092728000e6acb79

PDF]4HP13/14 SPLIT SYSTEM HEAT PUMP - Armstrong Air

www.armstrongair.com/_/.../Armstrong_4HP13L_Install_506318-01.pdf

4HP13/14 SPLIT SYSTEM HEAT PUMP .... indoor unit, outdoor unit contains system refrigerant charge for operation ... may be installed with up to 50 feet of line set (no more than ..... The defrost control incorporates 2 pressure switch .... Note: Sensor resistance decreases as sensed temperature increases. Pins/Wire. Color.Missing: tempstar

[PDF]RESIDENTIAL SPLIT HEAT PUMP SYSTEMS

icpindexing.toddsit.com/documents/086477/42808100101.pdf

This Manual Supports Split Heat Pump Units of The Above Series .... two groups is based on a difference in Defrost controls and/or the .... completes a circuit between µRµ ? µOµ in the the thermostat sub-base. 2. .... before connecting line voltage. ...Wire "S1" is the first stage of electric heat through the outdoor thermostat.

[PDF]Trane Installer's Guide Air Conditioner/Heat Pump 4TTZ0 ...

3 Ton Heat Pump Split System ' eBay

www.ebay.com/bhp/3-ton-heat-pump-split-system
eBayGoodman 3 Ton 14 SEER Heat Pump Split System GSZ140361 with Installation Kit.10k Heat Strip,Thermostat,Wiring, Disconnect Box,Pad. $1,912.00; Buy It ...

You need a heat pump thermostat. It comes with a wiring diagram.

need make and model numbers on both units.

Hi, if this is just a split standard heating and cooling unit, and not a split heat pump, all you need to do is pull stat wire from the indoor unit control board to control the condenser with 5 conductors, but you will only use 2 wires for the control of the condenser. Normally, the red and white tie to the 2 control wires of the contactor. Back at the control board, red to red and white to the Y or yellow terminal. You will also need to set your disconnect box for your high voltage near the condenser, where you will be coming from your breaker to supply high voltage to run the motors and compressor. Very easy to do. If it is a heat-pump, you will need to pull at least 8 conductor thermostat wire to wire this up. I would also need to know what terminals and kind of thermostat you have, and if you are using heat strips for second stage of heat. When you say standard unit, you will only need 2 control wires from the indoor to the outdoor unit, along with the high voltage. Please keep me posted and let me know if you need more help on this. A wiring schematic wouldn't be needed if its just a standard condenser.
Sincerely,
Shastalaker7
A/C, & Heating Contractor

you have stated no problem .only that you are wiring up a stat. thanks for sharing but what specifically are you looking for a stat ? a wiring diagram? what?is it a straight cool ? a heat pump? be specific please .

Could not find the E1Eh-020HA but found the E2 series


http://www.nordyne.com/Literature/707716c.pdf


http://www.nordyne.com/Literature/901a.pdf

Hope this helps. :]