Cant find where to change the batteries in the remote... There is no obvious place to put them unless we try to bust it open. Help!

the bottom of the battery goes against the spring
in the compartment where the batteries go there is an imprint in the plastic which shows the position of the battery

As i understand your quest you cant open the doors? Can you open the back trunk? If so you can disassamble the back seat wall and enter this way to the car. Post back.

Hi there,
There are two ways to do a reset on *********** board.

CMOS Jumper

1. Open your computer.
2. Look for a mother board jumper labeled as JBAT1, CLR CMOS, CLR TC or just a push button for a mid to high-end mobo. it should be placed near the BIOS or beside the CMOS battery.
3. It should look like this, as you can see there is a white triangle indicator and a number 3. The pins 1,2 are shorted, try to removed the pin and short pins 2,3.



4. Now put the jumper back to pins 1 and 2, it's all done. now you can go to bios and load defaults before you can change values.

CMOS Battery

1. Look for a 3v battery on the mother board.




2. Press the lock downward to remove the battery.
3. After removing the battery re install the battery. by doing this you have successfully cleared BIOS settings.

NOTE: 1. Check the fuse of your AVR if it is busted. replace the busted fuse with same rating.


2. Check your power supply. If it's dead try to fix it by replacing the fuse but it will require soldering tool and skills. 3. Your computer might still work but in my case the usb ports can only read flash drives after the lightning and the network interface card is busted.

Hopefully this information helps.
Thank you for using FixYa.

cant understand why you have no door lock it must have one unless you do not have the correct ket as its been changed at some time ,if so then i would climb under car with some twin flex cable from a 12v battery and then connect the`positive feed to the starter motor supplu and the other cable to the engine or gearboc then it will open with the remote

Giving you some hints. Battery leakage is one enemy of tv control and other remote control. They can corrode your battery spring contact, give contact bridges with neighboring tracks that can cause erratic behavior of your remote.

Some repairs can be done but doesn't guarantee success. First is try to clean the corrosion on battery contact = no power usually. Erratic behavior cause by contact bridging = battery leak residues.

Opening a remote control. Some have screws on its small foot. Covered by a rubber or sticker. Some are notch clip in strategic location you have to fry that one by one, opening first on its weakest side. In some don't want to be open.

Cleaning the board by a soft eraser is one way. After you open the remote. Commonly the button area where contact takes place.

If the first procedure and cleaning doesn't work. Buy new remote or use universal remote controller.

First Check to remote controller battery, on the lock side unless unlock and lock functions share the same battery. Next i would got o my local auto parts store and get a maintence/repair manual for 20.00 dollars from chiltons and see what the book has to say aout your problem. Sorry I cant be of more help.

if you cant even put the batteries in, how am i going to teach you to code it? there is diagram in side case showing PLUS up or down, follow it. both go in same way, why would you put neg to neg. do yu do that with flashlight batteries. come on.

Check the remote control for its infrared emission. Check it with fresh batteries. Check it by pressing all the keys. You can detect the presence of infra-red emission from the remote control, using a cell-phone camera. If you wish to get more details about how to check a remote control, please visit this site. One among the posts has details about it. In some cases, the remote control might need to clean.
http://electronicshelponline.blogspot.com/
http://remotesearch.blogspot.com/
http://homenol.blogspot.com/
Search the site by type in this key phrase "how to test a remote control "in the "search box at the top right of the display window of the Homepage" to get the related post quickly.
https://youtu.be/wUpnETSm6_k
https://www.youtube.com/watch?v=jsSCNCW3IbQ [open and clean]
https://www.youtube.com/watch?v=Qp-l1uh-5gE [open and clean]

Hey did you try holding the red button where you put the batteries and holding the red button where you put the SD card all unit have an button so it can read the sensor from unit to controller....

I think it does really happen that way on some things like that , maybe its the controling IC or a busted resistor inside your amp. and check your speakers too. maybe they are shorting inside that makes your amp malfunction. try too open it or its up to you.