I LOST THE CODE BOOK TO PROGRAM THE REMOTE WANTED TO PROGRAM THE CABLE BOX (MOTOROLA)

Motorola Cable box codes 0476 0810 0276 . I hope one of these helps. Unfortunately, if your cable box is newer than your remote or was released less than 6 months before the remote was programmed, the code you need may not be included. There is a bit of a time lag for releasing the codes to the makers of universal remotes. For more information and the code list try here: http://oneforall-na.com/remote.php?type=URC%203021 .

I hope this helps.

Cindy Wells

I have run into this problem with my Sharp Aquos as well. This is not necessarily a code problem but an interference problem.

If you take your hand or a thick book and sort of make a hood over the area of the sensor on the cable box and place the remote right up close to the sensor this will help let you know if the remote and the box are working with the code. Also might try turning off the TV or unplug the TV to test and make sure the remote will turn on the box.

Next thing after you determine this is how to block the interference and be able to use your remote. What we did is placed the Wii on top of the box over the area of the sensor and this seems to have done pretty good.

Good Luck ....

I happen to be a Jumbo Universal remote Expert here at Fixya, so I hope I can help. It is possible that this remote just won't run your Motorola cable box, but I wouldn't give up until I had tried the codes from the list in the manual, as well as run through the auto-setup feature of the remote for CBL and for SAT, where it just tries all the cable box codes one at a time.

I was able to find a working motorola codes for an Innovage Jumbo Remote, a three digit code remote you might as well try: 051.

You have probably tried the codes for Motorola (031) and GI (000, 032) from the manual using these steps:

1. Turn on the device with which you want to use the remote control.
2. Locate a 3-digit code for your device. (000, 031 & 032 for example)
3. Press and hold the corresponding button on the remote control
(CBL) for approximately three seconds. The POWER INDICATOR illuminates.
4. Enter the 3-digit code for your device within 30 seconds. The POWER INDICATOR shuts off.
5. Press the ON /OFF button to verify correct code entry. If the device shuts off, the code was entered correctly. If the device does not shut off, repeat steps 3-4, using a different code located on the Code List.

If those are still a bust, try the GI SAT codes 018 & 019.

Have you tried the following steps with both CBL and then SAT to search it's database?

1. Turn on the device with which you want to use the remote control.
2. Press and hold the corresponding button on the remote control
(SAT or CBL) until the POWER INDICATOR on the remote control illuminates. The remote control is in programming mode.
3. Press and release ON /OFF. The POWER INDICATOR on the remote control flashes once and stays on indicating the unit is in Power Scan mode.
4. Press CHANNEL UP or CHANNEL DOWN repeatedly until the device turns off.
5. When the device turns off, press any key to store the code.
6. Press any other button. If the device responds, the remote control has been programmed. If the device does not respond, repeat steps 2-5.

I hope that helps.

1. Find codes for each device and brand below.
2. Press and "HOLD" CODE SEARCH.
3. Press and release the TV, VCR or Cable button you want to set up. If programming AUX for a device, press and release AUX first and then the device to be programmed (TV, VCR or Cable). When the selected device button flashes proceed to the next step.
4. Enter the three digit code from the TV, VCR or Cable Box code lists.
   
   
5. Release CODE SEARCH.
6. With the device on, press another button, for example CHANNEL UP. If the device responds, no further programming is required. If the device does not respond, repeat steps 1-5 using another code number from the lists.

Here you go and it's FREE!!! =>

http://www.remotecentral.com/cgi-bin/files/dl.cgi?file=others/rca/rcr450-manual.zip&area=other

There is a code out there to try.  The code would be 47.  Just follow the steps in your manual on how to program this box and you should be able to go from there. Can't garantee that it will work as that code came out with the newer tv but it should work.

Try code 038. If that doesn't work try 039.

I got a a sharp LC-32D43U and for my motorola cable box i use hte code 31 from jerrold, i take it from the manual and i got it tryin every single code unti i get one that works.

Hope it works for you

Cable Converters (Set Top Boxes)

Director 0476
General Instrument 0476
Jerrold 0476
Motorola 0476, 1376
Pioneer 1877
Scientific Atlanta 1877

HOPE THIS WILL HELP YOU!!

Get on the phone with the provider and tell them you just can't seem to get the box to synch up. Ofter the book of lists provided is more or less universal and might not be specifically for yours. A call will generally get you further that an email chat, etc.