Keyless entry remote stopped working. Dealer wants $500+ to repair it. Looking for less expensive option.Keyless entry remote stopped working. Dealer wants $500+ to repair it. Looking for less expensive option.
AnonymousMar 28, 2014
Keyless entry remote stopped working. Dealer wants $500+ to fix it. Looking for less expensive option to repair it.Keyless entry remote stopped working. Dealer wants $500+ to fix it. Looking for less expensive option to repair it.
You can't post conmments that contain an email address.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
It does indeed have keyless entry. It needs reprogramming when you get a new remote. Also if you disconnect the battery. Usually a local car alarm fitting shop, or an auto-electrician will do it. Plus of course a Ford dealership.
Keyless entry remotes allow you to put down and roll up the windows in your car. You would have to have the power windows feature installed on your keyless remote. -------------------------------------------------------------------------------------- VVDI VAG Vehicle Diagnostic
Is this an issue with all 2008 HHR remotes??? Highly doubtful , probably the vehicles keyless entry system . Taking the vehicle to a qualified repair shop an having the keyless entry system checked for DTC'S - diagnostic trouble code's . Do you know what a DTC is ?
The keyless entry system is a vehicle entry device. The keyless entry system is used in conjunction with the body control module (BCM) to remotely activate certain vehicle features. Keyless entry will lock/unlock the doors, or release the rear compartment lid when a corresponding button on the keyless entry transmitter is pressed. This is accomplished by the transmitter sending a radio frequency to the remote control door lock receiver (RCDLR). The RCDLR interprets the signal and activates the requested function via a serial data message to the BCM. A low transmitter or vehicle battery or radio frequency (RF) interference from aftermarket devices, such as 2-way radios, power inverters, computers, etc., may cause a system malfunction. High RF traffic areas may also cause interference that could lead to a malfunction. Keyless entry allows you to operate the following components:
• Door locks
• Liftgate lock
• Remote rear doors (Panel only)
• Vehicle locator/panic alarm
• Illuminated entry lamps
• Remote vehicle start
The keyless entry system has the following components:
• Keyless entry transmitters
• Keyless entry antenna
• 2 Way Advanced Remote Start RCDLR
• BCM
You did it like this ?
Programming -Keyless Entry Remote Transmitter
NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time. NOTE: All previous transmitter identification codes (TIC's) will be erased when programming mode is entered. NOTE: To program (or reprogram) the keyless entry remote transmitters into the generic electronic module (GEM)(14B204), perform the following steps.
Turn the ignition from OFF to RUN eight times within 10 seconds, ending in RUN. If the GEM has successfully entered program mode, it will lock and unlock all the doors.
NOTE: The first TIC must be entered within 7.5 seconds of entering the program mode and additional TICs must be entered within 7.5 seconds of the first TIC. The programming mode is exited whenever the timing constraints are not met. Press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed.
If the door locks do not respond for any keyless entry remote transmitter, wait for several seconds and press the button again.
Turn the ignition switch to the OFF position, or wait up to five minutes after step 1, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the GEM will lock and unlock all the doors one last time.
Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming
NOTE: All keyless entry remote transmitters (15K601) must be
programmed at the same time. NOTE: To program (or reprogram) the keyless entry remote transmitters
into the RAP module, perform the following steps:
Make sure that the anti-theft system is not armed or triggered.
Turn the ignition switch (11572) from OFF to RUN eight times within ten
seconds, ending in RUN. If the RAP module has successfully entered program mode,
it will lock and then unlock all doors.
Within 20 seconds, press any button on a keyless entry remote transmitter,
and the doors will lock and then unlock to confirm that each keyless entry
remote transmitter has been programmed. Repeat this step for each
transmitter.
If the door locks do not respond for any keyless entry remote transmitter,
wait several seconds and press the button again. If the door locks still fail to
respond, refer to Inspection and Verification.
Turn the ignition switch to the OFF position, or wait up to 20 seconds after
step 2, to exit program mode. If a keyless entry remote transmitter has been
programmed (or reprogrammed), the RAP module will lock and unlock all doors one
last time to confirm.
The keyless entry matches to the module for it that is mounted under the dash. It may have gone bad since your remote will not function. Of course it could be your remote as well that went bad
does trunk button work? panic button?
here's 2003 info:
The doors do not lock/unlock using the remote transmitter
Remote transmitter.
Driver door module (DDM).
Go To Pinpoint Test G .
SECTION 501-14: Handles, Locks, Latches and Entry Systems
2003 Town Car Workshop Manual
GENERAL PROCEDURES
Remote Transmitter Programming
Cycle the ignition from OFF to RUN four times within three seconds. The locks will then lock and unlock, confirming that the program mode has been entered.
NOTE: When the first keyless entry remote transmitter is programmed, all other keyless entry remote transmitters are erased. Press any button on the transmitter to be programmed.
If additional keyless entry remote transmitters are to be programmed, repeat Step 2 within 7.5 seconds.
To exit program mode, turn the ignition to START or wait 7.5 seconds.
--------------------------------------------------------------
report back
Lock all the doors from the inside (with all the doors closed), unlock your driver's door by manually lifting the lock, then press it back down after you are out - this will prevent the alarm from sounding when you use the key to unlock the door.
i changed the battery and it still doesnt work
changed batteries both remote do not work
changed the battery on the keyless entry remote and it still doesnt work
Keyless remote stopped working.
Keyless entry remote stopped working. Dealer wants $500+ to repair it. Looking for less expensive option.
Keyless entry remote stopped working. Dealer wants $500+ to fix it. Looking for less expensive option to repair it.
×