Question about 2000 Daewoo Lanos

1 Answer

HOW WE CHANGE TIMMING BELT IN LANOS CARS - 2000 Daewoo Lanos

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,970 Answers

Mcdevito75 here, that is a shop job only, special tools may be needed to do this job. Best bet let your local repair shop do this job, It"s going to cost you more in time and effort to change the timeing belt than at the shop.

Posted on Jun 20, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crankshaft sensor location on lanos 2001 ? I changed my camshaft position sensor and the timing belt, but the engine light still on with the same code and the mechanic said it's the...


both the single cam and twin cam engines use the teeth on the crank pulley for crankshaft sensor which is bolted in bracket attached to block near oil pressure switch, hopefully you didnt dent(bent) teeth on crank pulley from dropping it or putting pulley down a bit roughly because they bend really eazy.
also is the crank pulley bolted up in correct position?
is the timming belt tension correct from when you did cam belt?
if tension wrong or timming out by a tooth it will set crank sensor codes, even possibly cam sensor codes and if you get timming out more than 3 teeth either way(advanced or ********) you will bend valves.

stevenhurc_26.jpg

Sep 05, 2011 | 2001 Daewoo Lanos

1 Answer

JUST CHANGED THE TIMMING BELT ON A DAEWOO LANOS NOW IT RUNS ROUGH.IT ALSO IDILES UP AND DOWN.SOME BACKFIRE.


you are out a tooth or two.engine must have moved a bit when you had it apart

Aug 01, 2010 | 2002 Daewoo Lanos

1 Answer

Engine noise in 1999 daewoo lanos


Check the condition of the tensioner and pulleys, a bearing may be bad in those items

Jun 02, 2010 | 1999 Daewoo Lanos

1 Answer

Cam shaft timming marks 1999 Daewoo 1.6 liter


there is a special tool to hold gears in correct place on some of these models, but you can hold one cam at a time with a spanner then feed belt on exhaust cam then inlet cam gear
get someone to hold gears in place while you feed belt on.
the inlet cam is more prone to turn off mark more than exhaust.
if you have tensioner that needs retaining pin in when installing
you fit belt while aligning timming marks
fit tensioner as last spot to feed belt on with retaining pin in adjuster
get correct tension on belt by turning water pump so that you can flex (turn) belt 90 degrees only just while using finger and thumb
tighten water pump check flex
check all timing marks are correct
remove retaining pin from auto tensioner
turn motor over a couple of turns by hand observing tensioner arrow should hover around V mark and that all timing marks align up again(after one complete turn)

Aug 02, 2009 | 1999 Daewoo Lanos

1 Answer

Timing belt tracking is bad on a 1999 Daewoo Lanos


  • was washer put back on the crank correctly? Is there spacers or gromits that hold the timming cover on? Sometime I run car before I put all excesserys back on just to see that problem...

Jul 21, 2009 | 1999 Daewoo Lanos

3 Answers

My timing belt in my 98 Daewoo Lanos snapped recently and the mechanic i took it to told me there was no need to check to see if there was any damage inside the engine because daewoo motors always drop...


yes they bend valves
head needs to come off and valves will need replacing
this can be repaired
timming belts on these should be replaced every 60,000km

Jun 26, 2009 | 1999 Daewoo Lanos

1 Answer

I need to know how to set the timming marks on the 1.6 double over head cams to replace timming belt


timming marks on cams face each other 3 and 9 o clock crank mark at about 6 o clock mark in cover and sump auto adjuster arrow should be in v mark to set this requires turning water pump by loosening water pump bolts slightly be warned some times this causes pump o ring seal to leak if turning.

May 19, 2009 | 2000 Daewoo Lanos

1 Answer

Remove and replace timming belt on lanos sx 1598cc 1998 thank you


First remove head and fix the bent valves. I have worked at a Daewoo dealer. People would buy the belt and come right back to get valves and gaskets. Daewoo timing belts must be replaced every 60,000 miles.

Apr 18, 2009 | 1999 Daewoo Lanos

1 Answer

Timming chain


No.....you do not have to change the timing chain due to being parked....it is wise though to follow manufactuers specs on WHEN to change it.

There is nothing wrong with your timing chain.

Mar 13, 2009 | 2001 Daewoo Lanos

Not finding what you are looking for?
2000 Daewoo Lanos Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75744 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...