How do i change windshield wipers on an 88 ford bronco 2?

If you are talking about a 1998 olds 88 then I would check the wiper pivot arms and the connection to the motor.

https://images.search.yahoo.com/search/images?p=windshield+wiper+parts+diagram&fr=mcafee&type=E211US1494G0&imgurl=http%3A%2F%2Fwww.chicagocorvette.net%2Fimages%2Fdiagrams%2Flarge%2FC-WINDSHIELD-07-wiper-system.gif#id=0&iurl=http%3A%2F%2Fwww.chicagocorvette.net%2Fimages%2Fdiagrams%2Flarge%2FC-WINDSHIELD-07-wiper-system.gif&action=click

In that year they used a wiper control module and the switch to control speeds and delay interval. The part is obsolete at the ford dealer and you may have to resort to salvage yard for part.

did they replace the engine temp sensor? it could be open and the computer sees -33 thinking the engine is cold and dumping fuel.

REMOVAL

1. Raise and support the hood.
2. Remove the windshield wiper pivot arms.
3. Remove the cowl top vent panels.

1. Disconnect the windshield wiper mounting arm and pivot shaft.

1. Remove the access cover from the dash panel.
2. Remove the mounting arm and pivot shaft retaining clip.
3. Disconnect the windshield wiper mounting arm and pivot shaft from the windshield wiper motor.

1. Remove the windshield wiper motor.

1. Disconnect the electrical connector.
2. Remove the three bolts.
3. Remove the windshield wiper motor.

INSTALLATION

1. Install the mounting arm and pivot shaft retaining clip on the windshield wiper mounting arm and pivot shaft.

1. Install the windshield wiper motor.

1. Place the windshield wiper motor in the dash panel.
2. Install the three retaining bolts.
3. Reconnect the electrical connector.

1. Reconnect the windshield wiper mounting arm and pivot shaft.

1. Press on the windshield wiper mounting arm and pivot shaft after it is aligned with the windshield wiper motor.
2. Install the access cover in the dash panel.

1. Install the cowl top vent panels.
2. Install the windshield wiper pivot arms.
3. Adjust the windshield wiper pivot arms.

This is technically for the V6 4.2L but I'm sure those Ford E250's have the same setup for windshield wiper motor. Let me know how it goes.

the problem was changing that fluid! rarely happen, but it will happen when people change transmission fluid on older car then the car messed up. when you change the fluid you washed all the friction material on the clutch surface by putting in new fluid.

well if it is a 1984 tranny it is a toyo koygo tk4 or tk5, which if mounted in the 84 bronco the transmission sets at a tilt, which means that the transmission crossmember bolts into the frame at a angle.. the mazda tranny was used in 88-90 the transmission crossmember sets straight across and bolts on to the frame on each side with one bolt.. with some major fabricating it is possible but to simply change out nope wont fit..

you should only have to pull the steering wheel and upper and lower housing on the column,

Below is the fuse lay out for 87 bronco, no wiper fuse is mentioned. if they do not work i would check to see if the wiper motor is getting power, if so then replace wiper motor

The 1996 Ford Bronco takes a 18" replacement wipers on both drivers side and passenger side. Don't just go by lengths though - when buying windshield wiper blades be sure to always use the application guide book at the store or now-a-days you can Google 'lookup wiper size'.

You want to look this up because correct wiper fit is more than correct length, it's also proper attachement. Not all attachments fit all arms. Using the application guide or looking up wiper size online will avoid headaches of buying the right lengths with the wrong attachements.

The replacement wiper blades will come with step-by-step, illustrated instructions and once you have the instructions and the wiper blades/arms in your hands in front of you, it will all make better sense and will an easy maintenance task. Very simple and takes 5-15 minutes usually not requiring any tools.

If in your budget, upgrade to the newer-style frameless "beam blades" which perform better than conventional framed wipers. I use Trico NeoForm Beam Blades which are fantastic. Hope this helps!

Put some ethernol treatment with stabilzer in it..
Change the fuel filter, air filter and give it an oil change...
If you can do it yourself do a trani service..