At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
start with 15 foot pounds, then 30 foot pounds, then 45 foot pounds, then finally 65 foot pounds, all the while bolting them down in a clockwise pattern working from the center out with each setting of foot pounds.
How much air should be in a car tire?
According to Berger the maximum inflation pressure for modern tires is typically between 44 and 51 PSI (pounds per square inch). If a driver inadvertently puts too much air in a tire it won't necessarily cause any damage, but it will impact other aspects of the vehicle.
Use a skin coat of RTV silicone on both sides of the water passage ports (outer most holes) and put the new lower intake gaskets into place
Hand tighten the 13mm head intake bolts and Torque the bolts , starting from the center and working your way out in a circular pattern
Torque these bolts in a few small increments until they have reached 250 inch pounds of torque.
Upper Intake Plenum:
When installing the intake air plenum , be sure to catch the four center bolts and the two side bolts (stiffener brackets) before tightening , The center bolts should be torqued to 250 inch pounds .The fuel rail bolts should be torqued to 100 inch pounds
Go to your local auto parts purchase a a/c charge kit for about $69.00, find the low pressure(suction) fill port, there are two ports in every a/c system one is a low pressure side used primarily to fill a system with freon 123a or the like and it is the larger valve mounted on the line, then there is the dangerous high side valve, this is a smaller diameter valve mounted to a smaller diamet a/c line, this is under extreme pressure so donot attempt to fill this high side with freon as it can backfire on you and cause injury.
The low side fill kit will not fit on the high side port so thank godness for that.
start the vehicle put the a/c on full cold high blow fan speed, start filling the low side with a can of 123a freon+oil additive, which equals one pound of freon and check the inside a/c vents, getting cold? If its perfect then you are done, the system may have a very small slow leak and if it only takes a one pound can to fill it once or twice a year you are ok, if it takes more you may want to add a second pound can of freon 134a containing a dye additive that will work its way into the system and show you where the leaks are by exposing a color once it hits the air coming out of the systems defective seals etc.,also they sell a sealer + freon one pound can that can be used to try to fix the leak without having to get too expensive on the repairs.
A car's air conditioning system only hold like 2 3/4 pounds of freon, so in the event you happen to over fill the system a high pressure blow valve usually mounted on the a/c compressor will purge off the excess, but let me warn you they blow off without any warning and can startle you. Always think safety first, wear protective equipment. Work Smart, Work Safe.
Happy Motoring!!!
it should be written on the tires. it will say max air press. usually you put it at about 4-6 pounds below what it says, depending on the ride you want
TRY TAKING OUT A 1/4 POUND BUT FIRST MAKE SURE THE CONDENSER IS CLEAN USE SPRAY 9 OR A SPRAY CLEANER ON THE CON AND RAD AFTER CLEANER SITS FOR 5 MIN FLUSH WITH A GARDEN HOSE AND TRY THE AC IF STILL NOT RIGHT LET OUT A 1/4 POUND
×