Go to ford owners.Com register then download the manual for free then go to roadside emergencies and your power distribution box diagrams and fuse box diagrams are in there and the fuse values and relay locations you can put this on your computer or phone and you can print it out and now you will always have it when you need it good luck stephen
Go to ford owners.Com and register for free then download the manual then go to roadside emergencies and your power distribution box diagrams and fuse values are in there and then you can get the information any time you need it from your phone or computer
×
SOURCE: I need a fuse number and location or a fuse box
1 15A* Adjustable pedals
2 — Not used
3 — Not used
4 20A* Power point - instrument panel
5 — Not used
6 20A* Trailer tow turn/stop relay
7 30A* High beam headlamps/Flash to pass
8 — Not used
9 — Not used
10 10A* A/C clutch
11 20A* Radio (main)
12 20A* Cigar lighter / OBD II
13 5A* Power mirrors/switches
14 15A* Daytime running lamps (DRL)
15 — Not used
16 — Not used
17 15A* Exterior lamps
18 20A* Turn lamps/Brake on-off switch (high)
19 10A* Body security module/4x4 module
20 — Not used
21 — Not used
22 20A* Engine control
23 20A* Engine control (gasoline engine only)
24 15A* Not used (spare)
25 10A* 4-Wheel Anti-lock Brake System (4WABS)
module
26 10A* Air bags
27 15A* Ignition switch Run feed
28 10A* EATC module/Front blower relay coil
29 10A* Customer access
30 15A* Highbeam headlamps
31 15A* Clutch interlock switch (manual
transmissions only), Transmission range
sensor (automatic transmissions only)
then to starter relay coil (all
transmissions)
32 5A* Radio (start)
33 15A* Front wiper
34 10A* Brake on-off switch
35 10A* Instrument cluster
36 10A* PCM Keep-Alive
37 15A* Horn
38 20A* Trailer tow park lamps and backup lamps
Roadside Emergencies
163
39 — Not used
40 20A* Fuel pump
41 10A* Instrument cluster
42 15A* Delayed accessory
43 10A* Fog lamps
44 — Not used
45 10A* Ignition switch Run/Start feed
46 10A* Left-hand lowbeam
47 10A* Right-hand lowbeam
48 — Not used
101 30A** Trailer tow electric brake
102 30A** Door locks/Body security module
103 50A** Ignition switch
104 — Not used
105 30A** Injector driver module (Diesel engine
only)
106 30A** Front wiper main
107 40A** Front blower motor
108 — Not used
109 30A** Heated seats
110 50A** Ignition switch
111 30A** 4WD/Shift on the fly
112 30A** Left-hand power seats
113 30A** Starter motor
114 30A** Right-hand power seats
115 20A** Trailer tow battery charge
116 30A** Ignition switch
601 30A CB*** Door window motors
602 60A** 4WABS module
210 — Not used
211 — Not used
Roadside Emergencies
164
212 — Not used
301 — Front blower motor relay
302 — Powertrain (EEC) relay
303 — Injector driver module relay (Diesel engine
only)
304 — Not used
305 — Trailer tow battery charge relay
306 — Delayed accessory relay
307 — Starter relay
SOURCE: 1999 Ford F-250 Super Duty 6.8 liter v10 is
You'll have to drain system down when cooled off, remove any brackets in your way such as power steering reservoir holding bracket, then remove 2 bolts holding the housing, and remove it. Rad hose should be o.k. to leave on, but if it creates a problem, remove it as well. I'd install a new thermostat and "o" ring complete,then a new gasket as well. Clean all surfaces well before re-installing. Replace any bracket(s) you removed to access housing, after housing is installed. Remember, air valve on edge of thermostat goes in 3 oclock position when re-installed. Also a reminder as well, spring on thermostat goes down when re-installed. After all is re-assembled, re-fill coolant and start engine and run with heater on to bleed out all air. Leave rad cap off and pay attention to temperature gauge and when you see it getting to normal operating temperature, watch flow in rad for increased flow, indicating thermostat opened and coolant is circulating properly. Wait until you see that flow increase 2 or 3 times, and air should be out of system, and top up coolant in rad, put cap back on, and check that return bottle is at proper level as well. Keep an eye for any leaks, and re-check return bottle periodically for first little while, just to be sure all is good. Note: some only use the "O" ring as a seal, and no gasket is required, but just check that at autoparts place where you get part.
SOURCE: 1999 ford f250 super duty 4x4 will go into 4
transfer case selector switch or equivlent to is bad or connectors to the switch is bad dose it do only when it rain or moisture underneath.
SOURCE: i need a fuse box diagram for a 05 ford f 250 super duty
my 2005 f250 diesel is all of a sudden not going into 4 x 4, no lights on dash now and cannot engage on wheels manually. Does anyone know where there is a fuse that operates this function that I can check?
SOURCE: i need a fuse panel
Here you go. This should be in your owners manual if you have one. If you need one and would like one, you can email me at [email protected] with your make, model, year and what you are looking for and I will be happy to email you a copy. Don't worry it won't cost you anything. This is for the fuse panel located inside the truck. i hope this helps and good luck.
84 views
Usually answered in minutes!
×